451434

Metabo HS 6001 Manual

13
Zoom out
Zoom in
Previous page
1/56
Next page
13
ENGLISH
2. Put both wheels (14) on the axle. To
do so the splitter's frame must be
slightly lifted by a second person.
3. Secure wheels on the axle by a split
pin.
5.4 Installing the Operating
Levers
1. On both operating levers (15) the
bolts (17) need to be pulled out
before installation:
− remove split pin (16);
− then pull bolt (17) out.
2. Fit operating lever (15) into the slot-
ted guide of the bracket. The lever is
fitted correctly if the claw is on the
top of the operating lever.
3. Put bolts (17) from the top through
the holes in the bracket and the
operating lever.
4. Secure bolt (17) with split pin (16)
from below.
5.5 Installing the Safety Gate
1. Fasten safety gate (19) as illustrated
with hexagon head screw, two
washers and prevailing torque-type
hexagon nut to the square tube (18).
Tigthen hexagon nut only so much
that the safety gate can easily be
lifted and lowered.
5.6 Installing the Support
Table
The support table can be installed in 3
different positions.
1. Rotate the two securing levers (22)
before installing the support table
(20) into correct position: the long
handle must point up.
2. Put support table into the holders
(21).
3. Rotate securing levers on both sides
into the recesses of the table rails.
5.7 Venting the Oil Reservoir
To avoid accidental escape of oil during
transport the oil reservoir cap is fully
closed for shipping.
Before initial operation the oil reservoir
cap must be opened so much that air
can escape from the reservoir.
A
Caution!
When the splitter is working the oil
reservoir cap must be opened to the
extent that the hydraulic oil reservoir
is vented.
1. Open oil reservoir cap (23) one full
turn, until the air can escape from
the reservoir.
5.8 Mains Connection
B
Danger! High voltage
Operate the splitter only on a power
source matching the following
requirements (see also "Technical
Specifications"):
− Outlets with neutral wire, properly
installed, grounded and tested.
− Mains voltage and frequency
must conform with the data
stated on the splitter's nameplate.
− Fuse protection by a residual cur-
rent device (RCD) of 30 mA fault
current sensivity.
− System impedance Z
max.
at the
interconnection point (house
service connection) 0.35 Ohm
maximum.
3
Note
Check with your local Electricity
Board or electrician if in doubt whether
your house service connection meets
these requirements.
Position power supply cable so it
does not interfere with the work and
is not damaged.
Protect power supply cable from heat,
corrosive liquids and sharp edges.
Use only rubber-jacketed extension
cables of sufficient lead cross section
(see "Technical Specifications").
Do not pull on power supply cable to
unplug.
5.9 Initial
Ooperation
A
Keep clear of the moving split-
ting knife!
To ensure safe transport, the splitting
knife is retained in the lowest position
for shipping. When the splitter is
turned ON the splitting knife raises
automatically. During initial opera-
tion, be sure that there is about one
meter of clearance available above
the splitting knife.
13
14
15
16
17
19
18
20
21
22
23
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo HS 6001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo HS 6001 in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info