Manual Metabo GB 18 LTX BL Q I (page 14 of 80) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

665602

Zoom out

Zoom in

1/80

ENGLISHen

and then turn fully in the direction

"AUF, RELEASE". The dust collected falls from

the keyless chuck.

7.9 Threadcutting Fig. G

Only use machine tappers, which fulfil the

following conditions:

- Only use undamaged and sharp machine taps.

- Only use machine taps for right-hand threads.

Preparations:

-Make a hole (with a diameter that fits the tap

used).

- Set the gear switch (4) to Gear "1".

- Move the sliding switch (3) to "Thread

tapping"

- Adjust setting wheel (12) (see fig. below):

The appropriate setting depends on many factors,

in principle the following applies:

a) Blind holes and small through holes:

For blind holes, do not select too much torque so

that the tap does not snap when it reaches the

bottom of the hole. The Pulse position corre-

sponds to the smallest torque and the smallest

speed. Both values increase up to position 4.

b) Through holes:

Select a larger torque. From position 4 the speed

remains the same and only the torque increases.

For "Maximum torque" select position .

-Open the chuck.

-Insert tap.

- Insert taps of sizes M8 - M12, to the stop in the

chuck so that the square is held by the holder

inside the chuck.

- Smaller taps are held sufficiently tight by the

clamping jaws of the chuck.

-Close chuck and clamp tight.

- Lubricate hole and tap with appropriate cutting

oil.

Tappingthread

- Place tap on the hole.

- Move machine in axial direction.

- Depress the trigger switch (14) and at a low speed

and with moderate pressure, let the tap cut into the

hole. The speed can be increased during the

thread tapping.

- When the desired thread depth is reached, pull

the machine evenly from the hole while keep the

trigger switch (14) depressed. The machine

automatically changes its direction of rotation.

Note:

If the sliding switch (3) is in the "Thread

tapping" position, right and left pulse functions

are not available.

Note:

If the sliding switch (3) is in the position

"Thread tapping" position and there is no

pressure on the tap, the machine runs in left mode!

If pressure is placed on the tap, the machine

automatically changes to right mode.

7.10 Chuck with quick-change system Quick

Fig. I

To remove: Push the interlock ring forward (a),

advance and pull off the chuck (b).

To fit: push the interlock ring forward and move the

chuck as far as the limit stop on the drill spindle.

7.11 Fitting the belt hook (equipment-

specific) / bit depot (equipment-specific)

Fig. J

Fit the belt hook (7) as shown.

Fit the bit depot (6) as shown.

8.1 The machine's multifunctional

monitoring system

If the machine switches off automatically, the

machine electronics have activated automatic

protection mode. A warning signal sounds

(continuous beeping). The beeping stops after a

maximum of 30 seconds or when the trigger switch

(14) is released.

In spite of this protective function, overloading

is still possible with certain applications and

can result in damage to the machine.

Causes and remedies:

1. Battery pack almost empty Fig. A, B (The

electronics protect the battery pack against

damage through total discharge).

If one LED (10) is flashing, the battery pack is

almost flat. If necessary, press the button (9) and

check the LEDs (10) to see the charge level. If

the battery pack is almost flat, it must be

recharged.

2. Long continuous overloading of the machine will

activate the temperature cut-out.

Leave the machine or battery pack to cool.

Note:

if the battery pack feels very warm, the

pack will cool more quickly in an "AIR COOLED"

charger.

Note:

the machine will cool more quickly if you

operate it at idling speed.

1...10

1/min

456

...

89107

8. Troubleshooting

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo GB 18 LTX BL Q I in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo GB 18 LTX BL Q I Manual

Product: