Manual Metabo FSX 200 INTEC (page 9 of 52) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

595422

Zoom out

Zoom in

1/52

ENGLISH en

7.2 Dust Extraction

To optimise the dust extraction performance, fit the

sanding disc such that the holes on the sanding disc

(1) are aligned to the support plate (2).

Integrated extraction system:

Install the dust collection box (4) (see illustration,

page 2). To optimise the extraction performance,

empty the dust collection box (4) in good time and

clean the filter (6).

External extraction system:

Fit dust extraction nozzle (see chapter on

Accessories). Connect a suitable extraction device.

Use a suction hose with a 35 mm connector

diameter. See Accessories section.

Empty dust collection box (4).

- Open cleaning flap (5).

- Empty dust collection box (4).

- Remove fluted filter (6) and knock off dust stuck to

filter or remove with brush.

- When inserting, ensure that the fluted filter (6) is

inserted in the lateral guides.

Clean the machine regularly. This includes

vacuum cleaning the ventilation louvres on the

motor.

Replacing a worn support plate (2)

- Remove fixing screws (on lower side of support

plate).

- Remove support plate.

- For replacement support plates, refer to the

Accessories chapter.

- Mount support plate.

- Refit fixing screws (on lower side of support plate)

and tighten.

Replacing support plate brake / braking ring

If the idling speed of the support plate increases in

the course of time, the braking ring is worn and must

be replaced in a service workshop for Metabo

power tools.

Note:

If abrasive material (e.g. gypsum, etc.) is

being sanded, the braking ring inevitably wears

faster.

Use only genuine Metabo accessories.

See page 4.

Use only accessories which fulfil the requirements

and specifications listed in these operating instruc-

tions.

A Support plate with velcro-type fastening

(as replacement)

B Adhesive intermediate disc

C Adhesive sanding discs

D Adhesive polishing sponge

E Lambskin adhesive polishing disc

F Adhesive polishing felt

G Adhesive sanding fleece

H Adhesive sanding screen

I Fluted filter (as replacement)

J Dust collection box (as replacement)

K Dust extraction connection

L Metabo universal vacuum cleaner

For complete range of accessories, see

www.metabo.com or the main catalogue.

Repairs to electrical tools must be carried out

by qualified electricians ONLY!

If you have Metabo electrical tools that require

repairs, please contact your Metabo service centre.

For addresses see www.metabo.com.

You can download spare parts lists from

www.metabo.com.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with European Guideline 2002/

96/EC on used electronic and electric equipment

and its implementation in national legal systems,

used power tools must be collected separately and

handed in for environmentally compatible recycling.

Explanatory notes on the specifications on page 3.

Changes due to technological progress reserved.

D =Dimensions of sanding plate

=Nominal power input

=Power output

=Idle speed

=Speed at rated load

=Orbital frequency at no load

=Orbital frequency at nominal load

S =Oscillating circuit diameter

Intec =Dust collection box

m =Weight without mains cable

Measured values determined in conformity with

EN 60745.

Machine in protection class II

~ Alternating current

The technical specifications quoted are subject to

tolerances (in compliance with the relevant valid

standards).

Emission values

These values make it possible to assess the

emissions from the power tool and to compare

different power tools. Depending on the operating

conditions, the condition of the power tool or the

accessories, the actual load may be higher or lower.

For assessment purposes, please allow for breaks

and periods when the load is lower. Based on the

adjusted estimates, arrange protective measures

for the user e.g. organisational measures.

Vibration total value

(vector sum of three directions)

determined in accordance with EN 60745:

8. Cleaning, Maintenance

9. Accessories

10. Repairs

11. Environmental Protection

12. Technical Specifications

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo FSX 200 INTEC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo FSX 200 INTEC Manual

Product: