511061
14
Zoom out
Zoom in
Previous page
1/100
Next page
14
ENGLISH
ENG
If the grinding wheel is so badly worn that the
maximum distance of 2 mm can no longer be
maintained, the grinding wheel must be replaced.
8.3 Switching On and Off
Press the switch (11) (see
illustrations D, page 3)
.
I
= Switch on
0
= Switch off
DS 125, DS 150:
Avoid inadvertent starts: always
switch the grinder off when the plug is removed
from the mains socket or if there has been a power
cut.
Restart protection (not in DS 125, DS 150):
When power is restored after a power failure, the
machine - which is still switched on - will not start
automatically for safety reasons. Switch machine
on and off again.
8.4 Dry grinding, belt sanding
- Stand in front of the grinder.
- Holding the workpiece with both hands, place
the workpiece on the workpiece supports (8) and
gently press it against the dry grinding wheel/
sanding belt. For optimum grinding/sanding
results, move the workpiece gently to and fro.
This also helps to distribute wear evenly on the
grinding material.
8.5 Wet grinding (TNS 175 only)
Only use the wet grinding wheel for grinding
when there is water in the water container.
(18). Roughly 1/3 of the wet grinding wheel should
be immersed in water. grinding results may
impaired if the water level is either too low or too
high.
- Stand to the left of the grinder, in front of the wet
grinding wheel.
- Holding the workpiece with both hands, lower it
onto the wet grinding wheel. You can also
support the workpiece on the levels on the water
container (18) and then lower the workpiece onto
the wet grinding wheel.
8.6
Adjusting the belt run
(BS 175 only)
Unplug. Rotate the sanding belt manually.
Use the rotary knob (14) to adjust the
sanding belt so that it runs centrally on the sanding
belt roller.
Clean, check and perform maintenance work on
the machine and guard devices regularly. Regu-
larly clean the inside of the grinding wheels and
belt grinder housing. The grinding wheels and
sanding belt must be able to rotate freely within the
housing.
Disconnect the mains plug before starting
any setting, cleaning, maintenance or repair
work.
9.1 Grinding wheel change
Use only original Metabo grinding wheels.
The permissible rotational speed specified
on the grinding wheel must be equal to or
greater than the maximum idling speed specified
on the identification plate of the machine.
Grinding wheel check:
suspend the grinding wheel on a thread.
Knock lightly with a piece of hard wood. You will
hear a clear tone if the grinding wheel is in perfect
condition. If you hear a clattering, dull or hollow
sound, the grinding wheel is damaged.
Do not use damaged grinding wheels.
Test run
A test run of approx. 5 min without load must
be carried out after the grinding wheel has been
changed. All persons must stay clear of the danger
zone when this is performed.
Dry grinding wheel:
- Release the screws on the safety guard cover (1),
twist and remove the cover (1) (bayonet catch).
- Hold the grinding wheel (4) firmly in position as
shown.
Caution! Risk of injury! Wear protec-
tive gloves!
9 Maintenance, cleaning
13
17026975_0611 DS DSD TNS BS.book Seite 14 Dienstag, 21. Juni 2011 1:48 13
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo DSD 250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo DSD 250 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info