511056
13
Zoom out
Zoom in
Previous page
1/100
Next page
ENGLISH
13
ENG
19 Rubber stopper *
* depending on equipment/not in scope of delivery
Bayonet catch on safety guards ensures quick,
easy replacement of grinding wheels
Low-noise, low-vibration, maintenance-free
induction motor
Vibration-absorbing rubber feet
BS 175, DS 175, DS 200, DSD 200, DSD 250,
TNS 175:
Safety guards with extraction connection piece
TNS 175:
Slow-speed, fine grained wet grinding disc and
high-speed dry grinding wheel
Corrosion-resistant water bath container
BS 175:
Large, tilting belt grinding arm (continuously
variable by 90°) for processing wood and metal
workpieces
7.1 Power supply
Before plugging in, check that the rated
mains voltage and mains frequency, as
stated on the rating label, match with your power
supply.
The grinder complies with protection class I and
must therefore only be connected to sockets
earthed according to specifications.
DSD 200, DSD 250 (three-phase version):
Ensure that the grinding wheels have the correct
direction of rotation (the correct direction of rota-
tion is indicated by an arrow on the side safety
guards). If a grinding wheel is rotating in the wrong
direction: Unplug the grinder. The plug comprises
of two phase conducting pins that are mounted on
a rotating socket (phase changing switch). Use a
Phillips screwdriver to rotate this socket.
7.2 Installing workpiece support
Install workpiece support (8) as shown in illustra-
tions A, page 3.
7.3 Fitting spark deflector and eye
preservers
Install the spark deflector (10) and eye preservers
(9) as shown in illustrations B, page 3.
7.4 Installing machine safely
Place the machine on a stable workbench. Ensure
that the machine is securely seated.
The machine can also be bolted down (screws not
included in the scope of delivery). To do this,
fasten the securing screws through the holes in the
rubber feet.
If a stand or wall bracket is used (see Accessories
chapter): bolt down the machine.
7.5 Dust extraction connection (depending
on equipment)
If your machine is not equipped with a
dust extrac-
tion connection (6), fit an extraction device that is
suitable for double-wheeled bench grinders
. Inner
diameter of extraction connection piece: 35 mm.
Before switching on the machine, ensure that the
extraction device is connected and being used
correctly.
7.6 Test run
Check the grinding wheels before initial use.
Test run
A test run of approx. 5 min without load must
be carried out before initial use. All persons must
stay clear of the danger zone when this is
performed.
.
8.1 Adjusting the workpiece support
Adjust the workpiece supports (8) frequently to
compensate for wear of the grinding wheels (4).
The distance between the workpiece support and
grinding material must be as small as possible and
never greater than 2 mm (see
illustration C, page
3)
.
If the grinding wheel is so badly worn that the
maximum distance of 2 mm can no longer be
maintained, the grinding wheel must be replaced.
8.2 Adjusting the spark deflector
Adjust the spark deflectors (10) regularly to
compensate for wear on the grinding wheels (4).
Release the 2 screws on the spark deflector and
shift the spark deflector.
The distance between the spark deflector and
grinding wheel must be as small as possible and
never greater than 2 mm (see
illustration C, page
3)
.
6 Special Product Features
7 Initial Operation
8Use
17026975_0611 DS DSD TNS BS.book Seite 13 Dienstag, 21. Juni 2011 1:48 13
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo DS 125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo DS 125 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info