625629
13
Zoom out
Zoom in
Previous page
1/96
Next page
ENGLISH
13
ENG
Metabo contact mode:
(KHE 26 Contact)
For intelligent drilling in walls with installed electric
or water lines. As soon as the inserted tool makes
contact with conductive, earthed material or live
supply cables, the machine switches off
immediately.
Metabo CODE! System
(KHE 28, KHE 26, BHE 26, KHE Partner Edition)
The Metabo CODE! System is an electronic anti-
theft device with which you can lock your Metabo
machines (if fitted with CODE!) to protect them
from abuse. Once locked, a machine can no longer
operate and therefore cannot be used by a
potential thief.
Wefore plugging in check to see that the
rated mains voltage and mains frequency,
as stated on the rating label, match with your
power supply.
7.1 Side handle installation
Wor safety reasons, always use the side
handle supplied.
Open the clamping ring by turning the side handle
(17) counter-clockwise. Place the side handle onto
the machine's collar. Insert the depth stop (7).
Tighten the side handle in the required angle
depending on the task at hand.
8.1 Depth Stop Setting
Loosen the side handle (17). Set depth stop (7) to
the desired drilling depth and retighten the side
handle.
8.2 Switching on/off
To start the machine, press the trigger (14).
The speed can be changed at the trigger.
This machine has an electronic soft start.
For continuous operation the trigger can be locked
with the lock button (13). To stop the machine,
press the trigger again.
If switched on continuously, the machine
continues running if it is jerked out of your
hands. Therefore, always hold the
machine with both hands on the handles, stand
safely, and concentrate on your work.
8.3 Speed preselection (KHE 26 Contact)
Depending on the application, the optimum speed
is preset with the pre-selector wheel (8).
8.4 Operating mode selection
Select the desired operating mode by turning the
control knob (16). To turn, push the stop (15).
twist drilling
hammer drilling
(only with use of hammer drill chuck)
chiselling
(KHE 28, KHE 26 Contact,
KHE 26,
KHE 22 SP,
KHE 24 SP,
KHE 26 SP, KHE Partner Edition)
(only with use of hammer drill chuck)
In chisel mode the chisel is locked to be twist-proof.
To position the chisel for the particular application,
set the control knob (16) between and
.
When a chisel is fitted, only operate
the machine in the chiselling operating
mode.
Avoid levering movements of the machine
when a chisel is fitted.
8.5 Selection of direction of rotation
Do not actuate the rotation selector
switch (12) unless the motor has
completely stopped.
Select direction of rotation:
R = clockwise
L = counter-clockwise
8.6 Drill chuck change
(not KHE 22 SP, KHE 24 SP, KHE 26 SP,
BHE 22, BHE 20 SP)
When changing chucks make sure that
the spindle is clean. Grease spindle lightly
if required.
Removing the chuck:
Turn chuck lock (5) in direction indicated by arrow
against the stop (a) and pull it off the spindle (b).
7Start of Operation
8Use
17026895_0308 BHE_Gu incl RU.book Seite 13 Montag, 31. März 2008 8:58 08
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BHE 26 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BHE 26 in the language / languages: All languages as an attachment in your email.

The manual is 4,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info