625636
8
Zoom out
Zoom in
Previous page
1/49
Next page
ENGLISHen
8
Australia: Always use a residual current
device (RCD) protected supply with a
rated residual current of 30 mA or less.
6.1 Side handle installation
For safety reasons, always use the side
handle supplied.
Open the clamping ring by turning the side handle
(1) counter-clockwise. Place the side handle onto
the machine's collar. Insert the depth stop (3).
Tighten the side handle in the required angle
depending on the task at hand.
7.1 Depth Stop Setting
Loosen the side handle (1). Set depth stop (3) to the
desired drilling depth and retighten the side handle.
7.2 Switching on/off
To start the machine, press the trigger (6).
The speed can be changed at the trigger.
For continuous operation the trigger can be locked
with the lock button (5). To stop the machine, press
the trigger again.
If switched on continuously, the machine
continues running if it is jerked out of your
hands. Therefore, always hold the machine
with both hands on the handles, stand safely,
and concentrate on your work.
7.3 Operating mode selection
Select the desired operating mode by turning the
control knob (8). To turn, push the stop (7).
Drilling
Hammer drilling
Chiselling
(KHE 2443 only)
In chiselling mode, the chisel is locked so that it
cannot turn.
To position the chisel for a particular application, set
the switch button (8) between and .
When a chisel is fitted, only operate the
machine in the chiselling operating mode
.
Avoid levering with the machine when a
chisel is fitted.
7.4 Setting the direction of rotation,
engaging the transporting safety device
(switch-on lock)
Do not activate the rotation selector switch (4)
unless the motor has completely stopped.
See page 2.
R=Clockwise setting
L = Counter-clockwise setting
Tool Change with SDS Chuck
Before fitting, clean tool shank and
apply special grease (accessories
order no. 6.31800)! Use only SDS-plus tools.
Inserting the tool:
Turn the tool while inserting, until it engages.
The tool is automatically locked.
Removing the tool:
Turn tool lock (2) in direction indicated by arrow
(a) and remove the tool (b).
The vent slots of the machine should be cleaned
from time to time.
If the trigger (6) can not be depressed, check to see
that the direction of rotation selector switch (4) is
fully set to the R or L position.
f
Use only genuine Metabo accessories.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
For a complete range of accessories, see
www.metabo.com or the catalogue.
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline
7. Use
8. Maintenance
9. Trouble Shooting
10. Accessories
11. Repairs
12. Environmetal Protection
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BHE 2243 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BHE 2243 in the language / languages: All languages as an attachment in your email.

The manual is 2,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info