658436
9
Zoom out
Zoom in
Previous page
1/60
Next page
ENGLISH en
9
Before plugging in, check to see that the
rated mains voltage and mains frequency,
as stated on the rating label, match with your
power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
To guarantee secure purchase of the
chuck: After initial drilling (clockwise), use a
screwdriver to firmly tighten the safety screw inside
the drill chuck. Caution left-handed thread! (see
Section 7.5)
7.1 Switching On and Off
To start the machine, press the trigger switch (5).
The speed can be changed using the trigger switch.
For continuous operation the trigger switch can be
locked using the lock button (6). To stop the
machine, press the trigger switch again.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine
with both hands using the handles provided,
stand in a safe position and concentrate.
7.2 Selection of direction of rotation
See illustration, page 2.
Do not activate the rotation selector
switch (4) unless the motor has
completely stopped.
Select direction of rotation:
R=Clockwise
L=Counter-clockwise
The drill chuck must be firmly screwed
onto the spindle and the safety screw
inside the drill chuck must be firmly tightened
with a screwdriver. (Caution, left-handed
thread!) If rotated counterclockwise (e.g. when
screwing) it could otherwise become loose.
7.3 Tool change with a geared chuck (2)
See illustrations, page 2.
Clamping tool:
Insert the tool and use the chuck key (1) to uniformly
clamp tight in all 3 bores.
Removing tool:
Open the geared chuck (2) with chuck key (1) and
remove tool.
7.4 Tool change
with keyless chuck (3)
See illustrations, page 2.
Insert tool. Hold ring (a) and turn the sleeve (b) with
your other hand in direction "GRIP, ZU" until further
rotation is impossible.
With a soft tool shank, retightening may be required
after a short drilling period.
Opening chuck: Hold ring (a) and turn the sleeve (b)
with your other hand in direction "AUF, RELEASE".
If the chuck is very securely tightened: Unplug.
Hold drill chuck using an open-end spanner at the
flats on its head and turn the sleeve (b) vigourously
in direction of "AUF, RELEASE".
7.5 Removing the chuck
Geared chuck (2)
Undo the locking screw. Caution left-handed
thread!
Hold the drill spindle tight with an open-ended
spanner. With a light blow from a rubber hammer,
release the chuck from the inserted chuck key and
unscrew it.
Keyless chuck (3)
Undo the locking screw. Caution left-handed
thread!
Hold the drill spindle tight with an open-ended
spanner. With a light blow from a rubber hammer,
6. Commissioning
7. Use
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BE10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BE10 in the language / languages: All languages as an attachment in your email.

The manual is 3,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info