595147
9
Zoom out
Zoom in
Previous page
1/60
Next page
ENGLISH en
9
Original instructions
1. Declaration of Conformity
We, being solely responsible, hereby declare that
these drills, identified by type and serial number *1),
meet all relevant requirements of directives *2) and
standards *3). Technical documents for *4) - see
page 3.
2. Specified Use
The drill is suitable for non-impact drilling into metal,
wood, plastic and similar materials. It is also
suitable for thread tapping and screwdriving.
The user bears sole responsibility for any damage
c
aused by improper use.
Generally accepted acciden
t prevention
regulations and the enclosed safety information
must be observed.
3. General Safety Instructions
For your own protection and for the
protection of your electrical tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety warn-
ings and instructions may result in electric shock,
fi
re and/or serious injury.
Keep all safety instructions and information for
fu
ture reference.
Pass on your electrical tool only t
ogether with these
documents.
4. Special Safety Instructions
Use the additional handle supplied with the
tool. Loss of control can cause personal injury.
Hold the power tool by insulated gripping
su
rfaces, when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory
contacting a “live” wire may make exposed metal
parts of the power tool “live” and could give the
operator an electric shock.
Pull the plug out of the pl
ug socket before any
adjustments or servicing are performed.
Avoid inadvertent starts by always unlocking the
switch wh
en the plug is removed from the mains
socket or in case of a power cut.
Ensure that the spot where you wish
to work is
free of power cables, gas lines or water pipes
(e.g. using a metal detector).
Smaller workpieces must be secured such that they
a
re not carried along with the drill bit when drilling
(e.g. by clamping in a vice or on a work bench with
screw clamps).
Keep hands away from the rotating tool!
Remove
chips and similar material only when the machine is
not in operation.
Metabo S-automatic safety clutch. When the safety
c
lutch responds, switch off the machine
immediately! If the tool jams or catches, the power
supply to the motor is restricted. Due to the strong
force which can arise, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
The Metabo S-automatic safety clutch mus
t not be
used for torque control.
Caution must be exercised when driving screws into
har
d materials (driving screws with metric or
imperial threads into steel)! The screw head may
break, or a high reverse torque may build up on the
handle.
Dust from material such as paint containing lead,
so
me wood species, minerals and metal may be
harmful. Contact with or inhalation of the dust may
cause allergic reactions and/or respiratory diseases
to the operator or bystanders.
Certain kinds of dust are classi
fied as carcinogenic
such as oak and beech dust especially in
conjunction with additives for wood conditioning
(chromate, wood preservative). Material containing
asbestos must only be treated by specialists.
- Where the use of a dust extraction device is
po
ssible it shall be used.
- The work place must be well ventilated.
- The use of a dust mask of filter class P2 is
re
commended.
Follow national requirements for the materials you
want to work with.
5. Overview
See page 2.
1 Thumbwheel for gear selection
2 Additional handle / Additional handle with
vib
ration damping *
3Geared chuck*
4 Futuro Plus keyless chuck *
5 Speed preselection se
tting wheel*
6 Electronic signal indicator*
7 Rotation selector switch
8 Locking button for continuous a
ctivation
9Trigger switch
* depending on equipment
6. Initial Operation
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
rating label, match with your power supply.
To ensure that the drill chuck is securely fitted:
After initial drilling (clockwise), use a
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BE 751 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BE 751 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info