658453

Metabo BE 622 S-R-L Manual

11
Zoom out
Zoom in
Previous page
1/64
Next page
ENGLISH en
11
See page 2.
1 Thumbwheel for gear selection
2 Additional handle / Additional handle with
vibration damping *
3Geared chuck*
4 Futuro Plus keyless chuck *
5 Speed preselection setting wheel*
6 Electronic signal indicator*
7 Rotation selector switch
8Locking button for continuous activation
9Trigger switch
* depending on equipment
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
rating label, match with your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
To ensure that the drill chuck is securely fitted:
After initial drilling (clockwise), use a
screwdriver to firmly tighten the safety screw inside
the drill chuck (if applicable / model-specific).
Caution left-handed thread !
(see Section 8.7.)
6.1 Assembly of additional handle (2)
For safety reasons, always use the additional
handle supplied.
Open the clamping ring by turning the additional
handle (2) counter-clockwise. Push the additional
handle onto the collar of the machine. Slide the
additional handle far enough forward so that it can
be turned. At the desired angle, pull it back and
tighten firmly.
7.1 Setting direction of rotation,
transport lock (switch-on lock)
Do not activate the rotation selector switch (7)
unless the motor has completely stopped.
See page 2.
R = Clockwise setting
L = Counter-clockwise setting
0 = Central position: transport lock setting
(switch-on lock)
The drill chuck must be firmly screwed onto
the spindle and the safety screw inside the drill
chuck (if applicable / model-specific) must be firmly
tightened with a screwdriver. (Caution, left-handed
thread !) If rotated counterclockwise (e.g. when
screwing) it could otherwise become loose.
7.2 Selecting a gear
Select the desired gear by turning the
thumbwheel (1).
Change speed only when the machine
is in the process of running down
(briefly switch it on and off).
1st gear (low speed, high torque)
e.g. for screwdriving, drilling
2nd gear (high speed) e.g. for drilling
7.3 Preselect speed
Use the setting wheel (5) to preselect the maximum
speed. See page 4 for recommended drilling
speeds.
7.4 Switching on/off, changing speed
Switching on, speed: press the trigger (9).
The speed can be changed by pressing in the
trigger.
The electronic soft start means that the machine
accelerates continuously until the preselected
speed is reached.
Release the trigger to switch off.
Continuous activation: While pressing on the
trigger (9), press in the locking button (8) and
then release the trigger. To switch off, press and
release the trigger (9) again.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in
a safe position and concentrate.
7.5 Tool change with
Plus (4)
chuck
See illustrations A, page 2.
Opening the drill chuck:
Using one hand, hold the retaining ring securely
and, using the other hand, turn the sleeve in the
direction of the arrow -1.
The ratchet sound which can possibly be heard
after opening the drill chuck is functional and is
switched off by a reverse rotation of the sleeve.
If the chuck is very securely tightened:
Unplug. Hold
the chuck using an open-end spanner at the flats on
its head, and turn the sleeve vigorously in the direc-
tion of the arrow -1.
Clamping the tool
- Insert the tool -2- as far as possible.
- Using one hand, hold the retainer ring securely.
- Turn sleeve in direction -3- until the noticeable
mechanical resistance has been overcome.
- Caution! The tool is not yet fully tightened!
Keep turning the sleeve (it must "click" when
turning) until it cannot be turned any further - only
now is the tool safely clamped.
With a soft tool shank, retightening may be required
after a short period of operation.
7.6 Tool change with a geared chuck (3)
See illustrations B on page 2.
Opening the drill chuck: Open the geared chuck
with chuck key -1.
5. Overview
6. Initial Operation
7. Use
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BE 622 S-R-L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BE 622 S-R-L in the language / languages: All languages as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info