658441
10
Zoom out
Zoom in
Previous page
1/68
Next page
ENGLISHen
10
Pull the plug out of the socket before making any
adjustments, changing tools, carrying out
maintenance or cleaning.
4.2 Special safety instructions for cordless
machines:
Avoid inadvertent starts by making sure that the
machine is switched off before fitting the battery
pack.
Remove the battery pack from the machine before
making any adjustments, changing tools,
maintaining or cleaning.
Protect battery packs from water and
moisture!
Do not expose battery packs to fire!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch contacts or short-circuit battery packs!
A slightly acidic, flammable fluid may leak
from defective Li-ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention
immediately!
LED lights (9): Do not observe the LED radiation
directly with optical instruments.
See page 2.
1 Futuro Top * keyless chuck
2 Side handle/Additional handle with vibration
damping
3 Thumb-wheel for gear selection *
4 Rotation selector switch
5 Speed preselection wheel *
6Trigger switch
7 Locking button for continuous activation
8Handle
9LED lights *
10 Battery pack release button *
11 Belt hook *
12 Battery pack *
13 Capacity and signal indicator *
14 Capacity indicator button *
* depending on the model / features
6.1 Assembly of the side handle (2)
For safety reasons, always use the additional
handle supplied.
- Open the clamping ring by turning the side handle
(2) counter-clockwise.
- Push the additional handle onto the collar of the
machine.
- Only for BE 600/13-2: Advance the side handle
until it can be twisted. Then pull it back into
position at the required angle.
- Tighten the side handle pulling firmly.
6.2 For mains powered machines only
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
6.3 For cordless machines only
Battery pack
Charge the battery pack (12) before use.
If performance diminishes, recharge the battery
pack.
The ideal storage temperature is between 10°C and
30°C.
Li-Ion battery packs "Li-Power" have a capacity and
signal indicator (13):
- Press the button (14), the LEDs indicate the
charge level.
- If one LED is flashing, the battery pack is almost
flat and must be recharged.
Removing and inserting the battery pack
Removal:
Press the battery pack release button
(10) and pull the battery pack (12) forwards.
To insert:
Slide the battery pack (12) in until it
engages.
Installation of belt hook
Attach the belt hook (11) as shown.
7.1 Setting the direction of rotation,
engaging the transporting safety device
(switch-on lock)
Only activate the rotation selector switch (4)
when the motor has completely stopped.
See page 2:
R = Clockwise setting
L = Counter-clockwise setting
0 = Central position: transportation lock setting
(switch-on lock)
7.2 Select the gear (depending on features)
Select the required gear by rotating the thumb
wheel (3).
Change speed only when the machine is in the
process of running down
(briefly switch On and Off).
1. st gear (low speed, high torque) e.g. for
screwdriving, drilling
2. nd gear (high speed) e.g. for drilling
5. Overview
6. Commissioning
7. Use
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BE 500-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BE 500-10 in the language / languages: All languages as an attachment in your email.

The manual is 5,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info