Manual Metabo BE 1100 (page 10 of 60) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

595146

Zoom out

Zoom in

1/60

ENGLISHen

screwdriver to firmly tighten the safety screw inside

the drill chuck (if applicable / model-specific).

Caution left-handed thread ! 

(see Section 8.7.)

6.1 Assembly of additional handle (2)

For safety reasons, always use the additional

handle supplied.

Open the clamping ring by turning the

additional

handle (2) counter-clockwise. Push the additiona

handle onto the collar of the machine. Slide the

additional handle far enough forward so that it can

be turned. At the desired angle, pull it back and

tighten firmly.

7. Use

7.1 Setting direction of rotation, 

transport lock (switch-on lock)

Do not activate the rotation selector switch (7)

unless the motor has completely stopped.

See page 2.

R =

Clockwise setting

L =

Counter-clockwise setting

0 =

Central position: transport lock setting

(switch-on lock)

The drill chuck must be firmly screwed onto

the spindle and the safety screw inside the drill

chuck (if applicable / model-specific) must be firmly

tightened with a screwdriver. (Caution, left-handed

thread !) If rotated counterclockwise (e.g. when

screwing) it could otherwise become loose.

7.2 Selecting a gear

Select the desired gear by turning the 

thumbwheel (1).

Change speed only when the machine 

is in the process of running down 

(briefly switch it on and off).

1st gear (low speed, high torque) 

e.g. for screwdriving, drilling

2nd gear (high speed) e.g. for drilling

7.3 Preselect speed

Use the setting wheel (5) to preselect the maximum

speed. See page 4 for r

ecommended drilling

speeds.

7.4 Switching on/off, changing speed

Switching on, speed: pres

s the trigger (9).

The speed can be changed by pressing in the

trigger.

The electronic soft start means that the ma

chine

accelerates continuously until the preselected

speed is reached.

Release the trigger to switch off.

Continuous activation: Wh

ile pressing on the

trigger (9), press in the locking button (8) and

then release the trigger. To sw

itch off, press and

release the trigger (9) again.

In continuous operation, the machine

continues running if it is forced out of your

hands

. Therefore, always hold the machine with

both hands using the handles provided, stand in

a safe position and concentrate.

7.5 Tool change with

Plus (4)

chuck

See illustrations A, page 2.

Opening the drill chuck:

Using one hand, hold the retaining ring securely

(depending on

equipment, not necessary for

BE 1300 Quick) and, using the other hand, turn the

sleeve in the direction of the arrow -1.

The ratchet sound which can possibly be heard

after op

ening the drill chuck is functional and is

switched off by a reverse rotation of the sleeve.

BE 751, BE 1100: If the chuck is very securely tight-

ened: Unplug. Hold the chuck using an open-end

spanner at the flats on its head, and turn the sleeve

vigorously in the direction of the arrow -1.

Clamping the tool

- Insert the tool -2- as far as possible.

- Using one hand, hold the retainer ring securely

(depen

ding on equipment; not required for

BE 1300 Quick).

- Turn sleeve in direction -3- until the noticeable

mechanical

resistance has been overcome.

- Caut

ion! The tool is not yet fully tightened!

Keep turning the sleeve (it must "click" when

turning) until it cannot be turned any further - only

now is the tool safely clamped.

With a soft tool shank, retigh

tening may be required

after a short period of operation.

7.6 Tool change with a geared chuck (3)

See illustrations B on page 2.

Opening the drill chuck: O

pen the geared chuck

with chuck key -1.

Clamping the tool: I

nsert tool -2- as far as possible

and, using the chuck key, evenly secure in all 3

bores -3.

7.7 Drill chuck with "Quick" change system

(for

BE 1300 Quick)

See illustration on page 2.

To remove: Push the interlock ring forward (a),

advance and pull off the chuck (b).

To mount: Pus

h the interlock ring forward and

move the chuck as far as the limit stop on the drill

spindle (slightly turn the chuck if necessary).

7.8 Unscrewing chuck (when screwing with-

out chuck or when using attachments)

See illustrations Y, Z on the second last page.

Note for illus. Y, Z: Release by tapping lightly with a

rubber hammer, as shown, and unscrew.

Note: If a bit clamping bush (order no. 6.31281) is

attached, the screwdriver bit inserted in the

hexagon socket of the spindle is held in place.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BE 1100 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo BE 1100 Manual

Product: