658553

Metabo BAS 318 Precision Manual

16
Zoom out
Zoom in
Previous page
1/104
Next page
ENGLISHen
16
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of
disused machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately
and handed in for environmentally compatible
recycling in accordance with European Directive
2002/96/EC on waste electrical and electronic
equipment and its implementation in national
legal systems.
Following you will find a description of problems
and faults that you may remedy yourself. If the
corrective measures described here do not help,
kindly refer to chapter 12. "Repairs".
Danger!
There are particularly many accidents in
connection with problems and faults. Therefore
keep in mind:
Disconnect the mains plug prior to any fault
service.
Check to see that all safety devices are
operational after each fault service.
Motor does not run
Undervoltage relay tripped by power failure:
– switch on again.
No mains voltage
– Check cables, plug, outlet and mains fuse.
Motor overheated, e.g. by a blunt band saw blade
or chip build-up in the housing:
– remove cause for overheating, let cool down
for a few minutes, then start again.
Motor and band saw blade turn in the wrong
direction
Connection sequence of the phases is reversed
(only possible with saw with 400 V connection):
– Have connection checked by a qualified
electrician.
Band saw blade wanders off the line of cut or
runs off the band saw wheels
Band saw blade is not running dead centre on the
band saw wheels:
– correct tracking (see "Care and
Maintenance").
Band saw blade breaks
Incorrect tension:
– correct band saw blade tension (see "Initial
Operation").
Load too high:
– reduce pressure against band saw blade
(reduced feed rate).
Incorrect band saw blade:
– replace band saw blade (see "Care and
Maintenance"):
thin work piece = narrow band saw blade,
thick work piece = wide band saw blade.
Band saw blade warped
Load too high:
– avoid lateral pressure on the band saw blade.
Saw vibrates
Insufficient mounting:
– Fasten saw properly to a suitable surface (see
"Initial operation").
Saw table loose:
– align and fasten saw table.
Motor mount loose:
– check fastening screws, tighten if necessary.
Dust extraction port blocked
No dust collector connected or suction capacity
insufficient:
– Connection extraction unit or increase
extraction power (air speed >= 20 m/sec at the
chip extraction nozzles).
Band saw blade is still while the motor turns
Belt tension too low:
– Increase belt tension using the setting knob
(40).
Explanations of the details on page xy.
Changes due to technological progress reserved.
U=Mains voltage
I=Rated power
F =Min. fuse protection
P
1
=Rated input power
P
2
=Power output
n
0
=No-load speed
v
0
=Cutting speed
S
L
=Band saw blade length
S
B
=Band saw blade width
S
D
=Max. blade thickness
H =Max. cutting height
W=Saw table swivel range
A
1
=Machine dimensions (LxWxH)
A
2
=Saw table dimensions (LxW)
A
h
=Working with frame
m=weight
D
1
=connection diameter of the extraction
nozzle
~ AC Power
Machine in protection class II
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be
higher or lower depending on the operating
conditions, the condition of the power tool or the
accessories. Please allow for breaks and periods
for assessment purposes when the load is lower.
Arrange protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Vibration total value
(vector sum of three
directions) determined in accordance with EN
61029:
a
h
=vibration emission value
K
h
= Uncertainty (vibration)
Typical A-effective perceived sound levels
:
L
pA
=sound-pressure level
L
WA
=acoustic power level
K
pA
, K
WA
= uncertainty
Wear ear protectors!
13. Environmental Protection
14. Troubleshooting Guide
15. Technical Specifications
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BAS 318 Precision at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BAS 318 Precision in the language / languages: All languages as an attachment in your email.

The manual is 26,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info