595141

Metabo B 32-3 Manual

10
Zoom out
Zoom in
Previous page
1/60
Next page
ENGLISHen
10
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers.
- Ensure good ventilation of the workplace and
keep it clean using a vacuum cleaner. Sweeping
or blowing stirs up dust.
Vacuum or wash protective clothing. Do not blow,
beat or brush.
See page 2.
1 Additional handle
2 Thread for screwing in the
additional handle
3Handle
4 Locking button (only for use in drill stand)
5 Trigger
6 Thumb-wheel for gear selection
7 Slot on machine neck
8 Removal tool
9 Drill spindle
10 Toolholder
Before plugging in, check to see that the rated
mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
The extension cable must be suitable for the
machine power rating (see Technical
Specifications). If using a roll of cable, always roll up
the cable completely.
6.1 Assembly of the additional handle
When the drill bit jams, very high torques may
be present. Therefore for safety reasons,
always use the additional handle (1) supplied.
In the event of jamming, it is not sufficient to hold the
machine only at the handle (3). There is a risk of
injury to the user.
Screw the additional handle (1) into the thread (2)
and pull firmly by hand.
7.1 Switching On and Off
Avoid load on the machine until it come to a
standstill.
Torque activation
To switch on:
press the trigger switch (5).
230 V: The rotational speed can be changed at the
trigger switch by pressing.
Switching off:
Release the trigger (5).
Continuous activation
(ONLY for use in drill stand):
To switch on:
press the trigger switch (5) and lock
with locking button (4).
To switch off:
press and release the trigger switch
(5).
Use the locking button (4) only when the
machine is in the drill stand.
The locking button (4) must be released after
every machine-related standstill or after a
current interruption to prevent accidental restart of
the machine (risk of injury) !
7.2 Three-speed gearing
Do not actuate the thumb-wheel (6) unless the
motor has completely stopped.
Select the desired speed by turning the thumb-
wheel (6).
If necessary, the switching procedure can be
supported by turning the drill spindle slightly.
7.3 Overload protection
The machine is equipped with a mechanical
overload protection device to protect the operator,
motor and tool.
If the tool jams suddenly, the drill spindle is
decoupled from the motor by means of a slip clutch.
The slip clutch is designed to absorb impact and
excessive load. As it is only an aid, and does not
provide total protection, you should always drill
carefully. To retain its operability, it should slip
through for a maximum of 2 seconds. In case of
excessive wear, it must be replaced by an
authorised specialist workshop.
7.4 Inserting and removing tool
Inserting
tool
:
Perfect seating of the tool in the drill spindle (9)
can only be guaranteed if the female taper of
the drill spindle and the taper shank of the tool are
free of dirt and grease.
Caution ! Never use excessive force to press
tools into the female taper of the drill spindle!
Always use sharp tools in perfect condition.
Switch off the machine. Pull the mains plug out
of the socket.
Tools with taper shank MK3 can be inserted directly
in the toolholder (10).
For all other tools, refer to the chapter 10.
Accessories and the illustration of page 4.
Removing
tool:
Insert the removal tool - with the sloping edge
against the drill - in the slot (7) on the machine neck.
If it cannot be inserted through the drill spindle, you
should turn it slightly by hand. Drive out the tool by
knocking lightly on the removal tool with a hammer.
Regularly clean the power tool’s air vents.
5. Overview
6. Commissioning
7. Use
8. Cleaning
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo B 32-3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo B 32-3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info