609956

Messner M 33000 Manual

12
Zoom out
Zoom in
Previous page
1/52
Next page
10
Please read these instructions thoroughly before using the pump!
This appliance is not suitable for use by persons (including children) with limited physical, sensory or mental
capabilities or lacking experience and/or knowledge, except if they are supervised by a person responsible
for their safety or have been instructed in the use of the appliance.
Children should be supervised in order to make sure that they do not play with the appliance.
Make
This modern, high-efficiency pump is equipped with a single-phase alternating-current motor (split tube
motor with capacitator). It is totally waterproof, embedded in solid plastic resin (IP68) and provided with an
overload protection.
Please refer to the type plate for technical specifications or the table on page 1.
Area of application: garden ponds, fishponds, outdoor and patio fountains!
These pumps are designed for the transport of water, for the operation of fountain jets, filter systems,
brooks, waterfalls, etc., as well as for the aeration and circulation of water.
- Attention! Use in garden ponds and their protected zone are permitted only if the installation is
performed in compliance with the applicable regulations. Please consult with a licensed electrician.
- Before performing any work on the pump, the fountain, or the pond, disconnect network plugs.
Do not operate the pump if people are in the water (disconnect the pump from the power source)!
Area of application: swimming pond or swimming pool (if people are in the water)!
These pumps are designed for the transport of water, for the operation of filter systems, aquatic attractions,
waterfalls, etc., as well as for the aeration and circulation of water.
Pump suitable for installation and operation in systems and rooms according to DIN VDE 0100 Part 702 and
Part 737, if the erection requirements per DIN VDE 100 and the manufacturer’s specifications (assembly
and operating instructions) are followed.
Installation of these pumps at swimming ponds or swimming pools must comply with the following
standards: DIN EN 13451 Part 1 to Part 8, and DIN VDE 0100 Part 702 and Part 737.
Attention! Operation of the pump is permitted here only if the pump is permanently installed outside
of the water at least 2 m or more from the pool.
The following measures must be undertaken: (see Figure 3)
- Install a shaft with pedestal for the pump, at least 2 m away from the edge of the water.
- Protect the shaft with a cover.
- To protect the pump from flooding, install a drain for the shaft.
- Bolt the pump to the pedestal.
- Install a metal bushing “M” in the suction line, toward the pump, for connection to the equipotential
bonding of the swimming pond/swimming pool system!
- Please consult with a licensed electrician.
Refer also to “Dry Installation” and “Safety Instructions”
Safety measures
- Before use: Check whether mains connection and plug are intact.
- Mains voltage and type of current have to correspond to the data on the type plate.
- The pump has to be connected to a regular safety plug socket through a residual current device
(RCD, 30 mA).
- The connection box should be located in a water-protected area. It should be at least 2 m away
from the edge of the pond (see fig. 1 + 2).
- Keep the plug dry!
- Pull out mains plug before starting to work on the pump, fountain or pond. It is not allowed to run
the pump when people are inside the water (disconnect the pump)!
- Important! When the mains connection or the motor housing are damaged, the pump cannot be used
anymore. It cannot be repaired since the connection is cast into the motor housing.
- Do never hang up or transport the pump by the cable!
Start-up (see fig.1 + 2)
Important! Do not let the pump run dry. This could cause damages to the appliance.
- Immerse the pump completely in your pond. This causes the pump body to be filled with water.
- A minimum water depth of 30 cm is required for underwater operation to avoid the pump taking in air.
- The maximum depth for submerged
2 m
operation of the pump is 2 m!
- The water temperature should not exceed 35°C.
- Do not let the pump freeze in the wintertime.
- The pump is switched on by putting the plug in the socket.
- To prevent the pump becoming unnecessarily dirty, place it above the mud in your pond, in a firm and
horizontal position (on a brick)!
GB
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Messner M 33000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Messner M 33000 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info