797759

Mesko MS 7741 Manual

7
Zoom out
Zoom in
Previous page
1/92
Next page
7
DEVICE OPERATION
HEATING OPERATION
1. Plug in the heater into a suitable socket.
2. Turn the thermostat knob (6) fully in a clockwise direction to the maximum setting “MAX”.
3. Turn on the heating elements by means of the rocker switches (8) on the side panel. When the heating elements are on the switches
(8) will illuminate by red lamp. There are 3 levels of heating power: 750W, 1250W and 2000W. For maximum heat output both switches
should be on.
4. When the desired room temperature has been reached, the thermostat knob (6) should be turned slowly anti-clockwise until the
thermostat is heard to click off and the lights on the element switches (8) are seen to go out. After this the device will keep the air
temperature in the room at the set temperature by switching on and off automatically.
FAN OPERATION
To speed up heating effect in room and get more warm air around switch on the fan switch (7) when rocker switches of heating power (8)
are switch on also. You can also switch on the fan switch (7) when rocker switches of heating power (8) are switch off to get more air
circulation in room.
TIMER OPERATION
This model is also equipped with a 24-hour clock which has 96 segments on its circumference, each representing 15 minutes of time.
With this timer, you can select the time and duration of the period (s) that the heater will operate at any time slot during the 24 hours.
* In the central position (denoted by the clock symbol) the timer will switch the heater on and off at times set by the segments, (see setting
the timer, below).
* In the position denoted by the “I”, timer will continue to run (the mini hand of the clock rotates inside the small clock on the thermostat
knob) but it will not work effective (not switching on and not switching off the heating). The power will be fed continuously to the heater.
This enables the heater to be on all the time if required.
* In the position denoted by the “0”, the timer continues to run (the mini clock hand rotates) but no power is fed to the heater.
Setting the Timer
Ensure the slide switch (10) on the timer knob (9) is at the mid position next to the clock symbol.
Rotate the outer ring of the timer in a clockwise direction until the current time is lined up with the arrow pointer, i.e. if the time the timer is
being set is 8 p.m., rotate the outer ring until the number 20 is in line with the arrow pointer.
Set the time the heater is required to run by moving the red segments located inside the ring. The segment is turn on (look at picture C
between 16:00 – 21:00, totally 5 hours) when it is slided to the OUTER edge of the ring. Move the number of segments appropriate to the
running period(s) required, one segment means 15 minutes of operation. If need to heat continuously by period of 3 hours starting from 8
p.m. then slide to the outer edge of the ring 12 adjacent segments between numbers 20 and 23.
When set, the heater will operate each day during the times programmed. Note, the heater must always be plugged into a power socket,
the rocker switches of heating elements (8) must be in the switch on position and the thermostat knob (6) must be suitably set to ensure
the device will start heating.
The segment is turn off when it is slided inside to the centre of the ring (look at picture C between 21:00 – 16:00, totally 7 hours).
If the heater is required to run continuously the slide switch (10) on the timer should be set to the “I” position.
If it is subsequently required to revert to timer operation, the slide switch (10) on the timer should be set to the central (clock) position.
Note: When using in timer mode, due consideration should be given to the fact that the heater may come on whilst unattended.
CLEANING AND MAINTENANCE
Make sure the device is not hot. Remove the plug from the socket before cleaning. Keep the inlet and outlet openings clean. Clean the
outside of the heater by wiping with a damp cloth and buff with a dry cloth. Do not use any detergents or abrasives and do not allow any
water to enter the heater. Do not immerse the device in water. Pack the device in bag to protect from the dust. Store it in a cool, dry place
until next use.
OVERHEAT PROTECTION
The device is provided with a safety system that automatically cuts the power to the heater in the event of overheating. If this event
occurs, switch the device off, remove the plug from the power outlet and wait until the device has cooled down (after about 10 minutes).
TECHNICAL DATA
Voltage: 220-240V~ 50Hz
Power: 1800-2000W
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste
bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may
effect the environment. Do not dispose this appliance in the common waste bin.
DEUTSCH
SICHERHEITSBEDINGUNGEN WICHTIGE HINWEISE ZUR SICHERHEIT BEI DER
VERWENDUNG BITTE SORGFÄLTIG DURCHLESEN UND FÜR SPÄTERES
NACHSCHLAGEN AUFBEWAHREN
Die Garantiebedingungen sind abweichend, wenn das Gerät gewerblich genutzt wird.
1. Lesen Sie vor der Verwendung des Produkts die folgenden Anweisungen sorgfältig durch
und befolgen Sie sie immer. Der Hersteller haftet nicht für Schäden aufgrund von
Missbrauch.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mesko MS 7741 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mesko MS 7741 in the language / languages: All languages as an attachment in your email.

The manual is 2.28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info