494943
21
Zoom out
Zoom in
Previous page
1/58
Next page
Customising 518: overview 21
518 User Guide
Customising 518, an overview
518 is a very sophisticated device with a huge number of options to allow
you to set up exactly the system you need or to experiment with new
possibilities.
Programming 518 is a straightforward process and you should not be
timid about experimenting. Although the setup is stored in non-volatile
memory called EEPROM, the EPROM (which you cannot change)
contains default Type settings and you can return to these at any time.
Restoring default settings
1. Switch off any power amplifiers that are connected to 518.
2. Switch off the 518 using the power switch on the back.
3. While pressing the Source key on the 518 front panel, switch the
power on again. The display will read:
4. Release the Source key
At this stage you can change the Type from 0 2 using the
n and s
Volume keys.
5. Switch off the 518 using the power switch on the back.
6. After half a second, switch the 518 power on again.
Caution Some power amplifiers are very susceptible to small surges that
may result from the process of switching a preamplifier on and off. Some
like the Meridian
205, 555 or 605 incorporate DC-offset protection that
may be triggered by this process. Meridian active or digital loudspeakers
are inherently proof against these surges and need not be switched off. In
general digital products like power amplifiers, recorders etc. will be
unpredictable when they have the digital signal interrupted.
518 has two setup options; Type and Config. These together with Normal
and Standby give the 518 four operating states. The following sections
give an overview.
Type: an overview
Type just described, restores one of the default settings. No further
actions are possible.
Config: an overview
Config mode is used for setting fundamentals of options and control.
Consequently in Config the outputs of 518 are muted while you make the
necessary choices. The choices available in Config are outlined in the
following sections.
Config: control settings
In Config you can make selections that effect the way 518 responds to
certain keys. The main choices of this kind are:
whether the 518 is to auto-configure, or you will determine the
controller in the system.
The ‘address’ of the product.
whether or not Standby is permitted.
1
1
Standby is not recommended for 'Pro' or Mastering situations
Type
1
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Meridian 518 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Meridian 518 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info