657614
77
Zoom out
Zoom in
Previous page
1/129
Next page
77
e
f
g
h
Adjusting the spring rate
To work perfectly, the suspension fork has to be adjusted
to the weight of the rider, the sitting posture and the in-
tended use. Be sure to have this adjustment carried out
by your MERIDA dealer at the time of delivery.
Note in general that the suspension fork must give in a
little even when you are just sitting on the bike – this is
the so-called negative suspension travel or sag
(e)
.
If you ride over a pothole the spring is decompressed
and the suspension fork compensates for the uneven-
ness. If the air pressure or the spring preload is too high,
this effect is lost because the suspension fork is already
fully extended. This means that an important comfort
and safety factor is lost if the tire briefly loses contact
with the ground.
In general, cross-country and marathon racers prefer a
shorter negative suspension travel (sag), freeriders or
downhillers riding often in rough terrain prefer a longer one.
In the case of cross-country and marathon bikes the sus-
pension fork should yield by 15-25 % of the maximum
suspension travel, in the case of all mountain, enduro
and freeride bikes by 25-35 %.
To measure the travel you can use the rubber ring mainly
located on the thinner, plunging tube of the suspension
fork. If there is no rubber ring, tie up a cable tie around
one of the stanchion tubes. Make sure it is not too tight,
you should still be able to move it, it should however not
slip by itself.
Put on your usual riding clothing (including if necessary
a packed rucksack), sit on your bike and bring yourself
into the usual riding position. Lean against a fixed object
(railings, wall etc.) and make sure you do not fall over.
Ask a helper to move the rubber ring or the cable tie
downwards against the dust seal at the lower leg
(f)
.
Get off your bike so that the fork does not compress any
more. The distance between the rubber ring/cable tie
and the wiper is the negative suspension travel, or sag
(g)
. Compare it against the total suspension travel (as
specified by the manufacturer) to determine whether the
suspension should be set to be harder or softer.
With pneumatic suspension forks the spring rate is set
by the air pressure in the fork. The pressure must be set
before the first ride by means of a special high-pressure
pump with pressure gauge
(h)
and modified later as re-
quired due to changes in the weight of the rider and/or
load.
Note the appropriate setting values and check them
subsequently at regular intervals. Always follow the rec-
ommendations of the manufacturer and never exceed
the maximum air pressure for the suspension fork. Al-
ways make a test ride after each change to the settings.
77


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Merida Pedelec at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Merida Pedelec in the language / languages: English as an attachment in your email.

The manual is 3,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info