657613
41
Zoom out
Zoom in
Previous page
1/129
Next page
41
e
f
g
h
G
The bolted connections of the seat post have
to be tightened to the prescribed torque val-
ue. Use a torque wrench and never exceed
the maximum torque values! You will find the pre-
scribed values in the chapter “Recommended torque
settings”, directly on the components and/or in the op-
erating instructions of the component manufacturers on
this MERIDA CD-ROM.
G
Make sure the saddle is clamped within the
range of the marking on the saddle rail
(e)
.
Otherwise the saddle rail can fail! Check the
bolts by using a torque wrench once a month according
to the prescribed values.
G
The setting range of the saddle is very small.
Replacing the stem allows you to make far
bigger adjustments to the riders fore-to-aft
position, as stems come in different lengths. In doing
so you may achieve differences of more than ten cen-
timeters. In this case you usually would have to adjust
the length of the cables – a job best left to your MERIDA
dealer!
I
The manufacturers of saddles deliver their
products with detailed instructions. You find
these instructions on this MERIDA CD-ROM.
Read them carefully before adjusting the position of
your saddle. If you are in doubt or if you have any ques-
tions, contact your MERIDA dealer.
Adjusting saddle position and tilt
With patent seat posts
(f)
one central Allen bolt secures
the clamping mechanism, which controls the tilt and the
horizontal position of the saddle. Some seat posts have
two bolts side-by-side.
Release the bolt(s) at the top of the seat post. Release
the bolt(s) two to three turns counterclockwise at the
most, otherwise the whole assembly can come apart.
Move the saddle forth or back, as desired. You may have
to give the saddle a light blow to make it move. Please
observe the markings on the saddle rail.
Make sure the seat of the saddle remains horizontal
(g)
as you retighten the bolt(s). Your MERIDA bike should
stand on level ground while you adjust the saddle.
Having found your preferred position, make sure both
clamp halves fit snugly around the saddle rails before
tightening the bolt(s) to the correct torque value as pre-
scribed by the seat post manufacturer.
Retighten the bolt(s) with a torque wrench according to
the instructions of the manufacturer
(h)
. After fastening
the saddle, check whether it resists tilting by bringing
your weight to bear on it once with your hands at either
end of the saddle.
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Merida Mountain Bike at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Merida Mountain Bike in the language / languages: English as an attachment in your email.

The manual is 3,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Merida Mountain Bike

Merida Mountain Bike User Manual - German - 134 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info