624676
408
Zoom out
Zoom in
Previous page
1/438
Next page
Mounting a wheel
Preparing the vehicle
X
Stop the vehicle on solid, non-slippery and
level ground.
X
Apply the electric parking brake manually.
X
Bring the front wheels into the straight-ahead
position.
X
Shift the transmission to position P.
X
Make sure that "normal" level is selected for
AIRMATIC (
Y page 212) or Active Body Con-
trol (ABC) (
Y page 210).
X
Switch off the engine.
X
Open the driver's door.
The on-board electronics now have status 0.
This is the same as the SmartKey having been
removed.
X
Remove Start/Stop button from ignition lock
(
Y page 162).
or, if the SmartKey is inserted in the ignition
lock:
X
Remove the SmartKey from the ignition lock.
X
Make sure that the engine cannot be started
via your smartphone (
Y page 164).
X
If included in the vehicle equipment, remove
the tire-change tool kit from the vehicle.
X
Safeguard the vehicle against rolling away.
Securing the vehicle to prevent it from
rolling away
If your vehicle is equipped with a wheel chock, it
can be found in the tire-change tool kit
(
Y page 367).
The folding wheel chock is an additional safety
measure to prevent the vehicle from rolling
away, for example when changing a wheel.
X
Fold both plates upwards :.
X
Fold out lower plate ;.
X
Guide the lugs on the lower plate fully into the
openings in base plate =.
X
Place chocks or other suitable items under
the front and rear of the wheel that is diago-
nally opposite the wheel you wish to change.
Raising the vehicle
G
WARNING
If you do not position the jack correctly at the
appropriate jacking point of the vehicle, the
jack could tip over with the vehicle raised.
There is a risk of injury.
Only position the jack at the appropriate jack-
ing point of the vehicle. The base of the jack
must be positioned vertically, directly under
the jacking point of the vehicle.
!
The jack is designed exclusively for jacking
up the vehicle at the jacking points. Other-
wise, your vehicle could be damaged.
Observe the following when raising the vehi-
cle:
R
To raise the vehicle, only use the vehicle-spe-
cific jack that has been tested and approved
by Mercedes-Benz. If used incorrectly, the
jack could tip over with the vehicle raised.
R
The jack is designed only to raise and hold the
vehicle for a short time while a wheel is being
changed. It must not be used for performing
maintenance work under the vehicle.
R
Avoid changing the wheel on uphill and down-
hill slopes.
R
Before raising the vehicle, secure it from roll-
ing away by applying the parking brake and
406
Changing a wheel
Wheels and tires
408


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mercedes S550e at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mercedes S550e in the language / languages: English as an attachment in your email.

The manual is 11,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info