703622
324
Zoom out
Zoom in
Previous page
1/398
Next page
Programming
Programming the buttons
Pay attention to the "Important safety notes"
(
Y page 321).
Garage door remote control A is not included
with the integrated garage door opener.
X
Turn the SmartKey to position 2 in the igni-
tion lock (
Y page 140).
X
Select one of buttons ; to ? to use to con-
trol the garage door drive.
X
To start programming mode: press and
hold one of buttons ; to ? on the integrated
garage door opener.
The garage door opener is now in program-
ming mode. After a short time, indicator
lamp : lights up yellow.
Indicator lamp : lights up yellow as soon as
button ;, = or ? is stored for the first time.
If the selected button has already been pro-
gramed, indicator lamp : will only light up
yellow after ten seconds have elapsed.
X
Release button ;, = or ?. Indicator
lamp : flashes yellow.
X
To program the remote control: point
garage door remote control A towards but-
tons ; to ? on the rear-view mirror at a dis-
tance of 2 to 8 in (5 to 20 cm).
X
Press and hold button B on remote control
A until indicator lamp : lights up green.
When indicator lamp : lights up green: pro-
gramming is finished.
When indicator lamp : flashes green: pro-
gramming was successful. The next step is to
synchronize the rolling code (
Y page 322).
X
Release button B on remote control A for
the garage door drive system.
If indicator lamp : lights up red: repeat the
programing procedure for the corresponding
button on the rear-view mirror. When doing
so, vary the distance between remote control
A and the rear-view mirror.
The required distance between remote con-
trol A and the integrated garage door opener
depends on the garage door drive system.
Several attempts might be necessary. You
should test every position for at least
25 seconds before trying another position.
Synchronizing the rolling code
Pay attention to the "Important safety notes"
(
Y page 321).
If the garage door system uses a rolling code,
you will also have to synchronize the garage
door system with the integrated garage door
opener in the rear-view mirror. To do this you will
need to use the programming button on the door
drive control panel. The programming
button
may be located in different places depending on
the manufact
urer. It is usually located on the
door drive unit on the garage ceiling.
Familiarize yourself with the garage door drive
operating instructions, e.g. under "Program-
ming additional remote controls", before carry-
ing out the following steps.
Your vehicle must be within reach of the garage
door or gate opener drive. Make sure that nei-
ther your vehicle nor any persons/objects are
present within the sweep of the door or gate.
X
Turn the SmartKey to position 2 in the igni-
tion lock (
Y page 140).
X
Get out of the vehicle.
X
Press the programming button on the door
drive unit.
You now have 30 seconds to initiate the next
step.
X
Get into the vehicle.
X
Press previously programed button ;, =
or ? on the integrated garage door opener
repeatedly until the door closes.
The rolling code synchronization is then com-
plete.
Notes on programming the remote con-
trol
Canadian radio frequency laws require a "break"
(or interruption) of the transmission signals
after broadcasting for a few seconds. Therefore,
these signals may not last long enough for the
integrated garage door opener. The signal is not
recognized during programming. Comparable
322
Features
Stowage and features
324


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mercedes GLS 2018 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mercedes GLS 2018 in the language / languages: English as an attachment in your email.

The manual is 7,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mercedes GLS 2018

Mercedes GLS 2018 Additional guide - English - 194 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info