703603
306
Zoom out
Zoom in
Previous page
1/374
Next page
with Canadian law, some U.S. garage door open-
ers also feature a "break".
Proceed as follows:
R
if you live in Canada.
R
if you have difficulties programming the
garage door opener (regardless of where you
live) when using the programming steps.
X
Press and hold one of buttons ; to ? on the
integrated garage door opener.
After a short time, indicator lamp : lights up
yellow.
X
Release the button.
Indicator lamp : flashes yellow.
X
Press button B of garage door remote con-
trol A for two seconds, then release it for two
seconds.
X
Press button B of the remote control A
again and hold for two seconds.
X
Repeat this sequence on button B of remote
control A until indicator lamp : lights up
green.
When indicator lamp : lights up green: pro-
gramming is finished.
When indicator lamp : flashes green: pro-
gramming was successful. The next step is to
synchronize the rolling code.
X
Release button B of remote control A of the
garage door drive.
If indicator lamp : lights up red: repeat the
programming process for the corresponding
button on the rear-view mirror. When doing
so, vary the distance between remote control
A and the rear-view mirror.
The required distance between remote con-
trol A and the integrated garage door opener
depends on the garage door drive system.
Several attempts might be necessary. You
should test every position for at least
25 seconds before trying another position.
Problems when programming
If you are experiencing problems programing
the integrated garage door opener on the rear-
view mirror, take note of the following instruc-
tions:
R
Check the transmitter frequency used by
garage door drive remote control A and
whether it is supported. The transmitter fre-
quency can usually be found on the back of
remote control A for the garage door drive.
The garage door opener is compatible with
devices which operate in the frequency range
of 280 to 433 MHz.
R
Replace the batteries in garage door remote
control A. This increases the likelihood that
garage door remote control A will transmit a
strong and precise signal to the integrated
garage door opener.
R
When programming, hold remote control A
at varying distances and angles and from but-
tons ; to ? which you are programming. Try
various angles at a distance between 2and
8 inches (5to 20 cm) or at the same angle but
at varying distances.
R
If another remote control A is available for
the same garage door drive, repeat the same
programming steps with this remote control
A. Before performing these steps, make sure
that new batteries have been installed in
garage door drive remote control A.
R
Note that some remote controls only transmit
for a limited amount of time (the indicator
lamp on the remote control goes out). Press
button B on remote control A again before
transmission ends.
R
Align the antenna cable of the garage door
opener unit. This can improve signal recep-
tion/transmission.
Opening/closing the garage door
After it has been programmed, the integrated
garage door opener performs the function of the
garage door system remote control. Please also
read the operating instructions for the garage
door system.
X
Turn the SmartKey to position 2 in the igni-
tion lock (
Y page 132).
X
Press button ;, = or ? which you pro-
grammed to operate the garage door.
Garage door system with a fixed code: indi-
cator lamp : lights up green.
Garage door system with a rolling code: indi-
cator lamp : flashes green.
The transmitter will transmit a signal as long
as the button is pressed. The transmission is
halted after a maximum of ten seconds and
indicator lamp : lights up yellow.
X
Press button ;, = or ? again if necessary.
304
Features
Stowage and features
306


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mercedes GLC 2017 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mercedes GLC 2017 in the language / languages: English as an attachment in your email.

The manual is 6,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mercedes GLC 2017

Mercedes GLC 2017 Additional guide - English - 178 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info