467160
15
Zoom out
Zoom in
Previous page
1/19
Next page
15
Programming Pads
Oven is shipped from the factory for single pad programming. To change
the oven default to allow double pad programming, see User Options.
To change the amount of time or the power level for a preset pad:
1. Open oven door.
READY displays.
• If door is closed or RESET pad is pressed before programming
is complete, changes are discarded and microwave exits
programming mode.
2. Press and hold pad 1 for approximately 5 seconds.
• This begins programming mode.
• Microwave will beep and P:0 displays. Oven is in
programming mode.
3. Press pad to be reprogrammed.
• Press two pads if reprogramming a double pad program.
COOK LEVEL and cooking time display.
• A number displays with COOK LEVEL if it is less than full power.
4. Enter cooking time by using the number pads.
5. Press POWER LEVEL pad to change power level if desired.
• Use the number pads to change power level to a lower
power setting.
6. Press START pad to set new programming to the pad.
• If START is not pressed, changes will not be saved.
P:0 displays
7. Press STOP/RESET pad or close oven door to exit
programming mode.
Programming Multiple Stages
Stage cooking allows consecutive cooking cycles without interruption.
Up to four different cooking cycles can be programmed into a memory
pad. To use stage cooking:
1. Follow steps 1 through 5 above.
6. Press TIME ENTRY pad.
• Display briey shows the pad number that is being
programmed and the stage number to the upper right.
Display changes to cook time and power level for the next stage.
7. Enter cook time and power level as in steps 4 and 5.
To enter another cooking stage for that pad, press TIME ENTRY
pad again.
• Up to four different stages can be programmed.
8. Press START pad to set new programming changes to the pad.
X2 Programming
This feature allows a preset
percentage of original cook
time, called a cooking factor, to be
added to a cook sequence.
To change the cooking factor:
1. Open oven door.
2. Press and hold pad 1 for
approximately 5 seconds.
3. Press pad to be reprogrammed.
4. Press the X2 pad.
5. Press a numbered pad to
change the cooking factor.
• Pad 5 would change the
cooking factor to 50%.
• Pad 3 would change the
cooking factor to 30%.
6. Press START pad to save changes.
Programming
STYLE 2
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Menumaster (Amana) DEC21E2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Menumaster (Amana) DEC21E2 in the language / languages: English as an attachment in your email.

The manual is 1,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Menumaster (Amana) DEC21E2

Menumaster (Amana) DEC21E2 User Manual - German - 19 pages

Menumaster (Amana) DEC21E2 User Manual - Dutch - 12 pages

Menumaster (Amana) DEC21E2 User Manual - French - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info