820638

Memphis Grills MG01-06-001 Manual

12
Zoom out
Zoom in
Previous page
1/37
Next page
12
Item # NAME Wire Idencaon DESCRIPTION / INSTRUCTION
1 Auger Motor
Wiring
1x Black Wire, 1x White Wire
Snap Disk
Leads Extending from Auger
Motor
Aach the white wire shown to one of the leads extending from the
auger motor. Aach the black wire to the snap disk as shown. The
2nd lead extending from the auger motor aaches to the opposite
side of the snap disk as shown. The snap disk is a thermal switch
which will cut power to the auger motor in the event that its crical
temperature is reached.
2 RTD Wiring 1x Orange Wire, 1x Brown Wire Aach both spade connectors to the leads extending from the RTD
as shown above.
3 Grounding Wire Green Wire The connecon point for the ground is located on the auger motor
gearbox body as shown.
4 Ethernet Cable Black Cable with Ethernet End
Aach the Ethernet cable to the terminal on the Wi-Fi card as
shown. Ensure that the wiring does not interfere with the auger
motor’s moving components.
5 Igniter Wiring 1x Red Wire, 1x White Wire Aach both spade connectors to the leads extending from the
igniter. These leads will extend from next to the fan.
6 Fan Wiring 1x Blue Wire w/ 2 spade ends,
1x White Wire w/ 2 spade ends
Aach the connecons on this jumper to the two tabs located on
the side of the fan housing.
7 USB Port N/A Used to update your grill.
8 Meat Probe
Wiring
1x Red Wire 1x Black Wire,
Wires twisted around each
other
This terminal is used to connect the meat probes to the controller.
9 120/240 Select
Jumper 1x Black Wire Used when changing the input voltage to the controller, see “120v
to 240v Conversion” secon of the main manual for informaon.
10
AC Load Wire
from Filter to
Controller
1x Black Wire
Carries AC voltage from the lter to the control board, load wire.
11
AC Neutral Wire
from Filter to
Controller
1x White Wire
Carries AC voltage from the lter to the control board, neutral wire.
12 Filter N/A Reduces electrical feedback. Line = Outlet Side, Load = Grill Side. L1
= Load L2= Neutral
13 MOV + Fuse
Holder
1x Red Wire 1x White Wire.
Pair is joined in the middle with
black shrink wrap. Fuse holder is
cylindrical and white plasc.
A two-wire component, which has a ferrite choke to eliminate input
electrical disturbances from the grid, connects to Load and Neutral
terminals. Fuse holder accepts a 5 amp glass fuse.
CONTACT YOUR DEALER OR MEMPHIS GRILLS TECHNICAL SERVICE WITH ANY QUESTIONS.
TECHNICAL SERVICE NUMBER: 1-888-883-2260
Memphis Control Diagram continued
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Memphis Grills MG01-06-001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Memphis Grills MG01-06-001 in the language / languages: English as an attachment in your email.

The manual is 6.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info