799552

Mellerware Vortex - 31100 Manual

6
Zoom out
Zoom in
Previous page
1/35
Next page
3.4.5.3. Hold the lter by the edges and “TAP CLEAN”
on a hard, at surface until the dust particles are
removed from between the pleats of the lter.
3.4.5.4. The HEPA type lter may also be washed with
lukewarm water by holding it under a running tap and
allowing the water to run on the dirty side. We recom-
mend washing it at least once a month depending on
how often you use it or when the suction appears to
reduce.
3.4.5.5. Always allow the lter to air dry for at least 24
hours before placing it back into the vacuum.
NB Ensure the lter is completely dry before placing
back into the vacuum.
3.4.5.6. Reinstall the lter into the dust cover and click
it back onto the dust bin.
Please Note that it is normal for the lter to discolor
over time, this will not affect the performance of the
lter.
3.4.6 Reinstalling the dust bin:
3.4.6.1. Ensure that the small intake air vent on the
dust bin is aligned with the opening on the main unit.
3.4.6.2. Slide the dust bin into place and push back
until you hear it lock into place.
CAUTION: The suction hole must be open and free of
any obstructions at all times. Otherwise, the motor will
overheat and could become damaged.
Warning: Always empty the dust bin container and
clean the HEPA type lter after each use and during
prolonged usage.
Never over ll the dust bin container, remove dirt and
clean the HEPA type lter when dirt in dust bin is at or
just below the “MAX” level during prolonged usage or
risk motor damage.
If you wash the HEPA type lter, ensure that it is com-
pletely air dry before inserting back in the vacuum.
Please Note: The HEPA type lter is washable. It
should, however, be replaced when damaged. Replace-
ment lters are available at Creative Housewares.
Contact details are below.
3.5 Once you have nished using the appliance:
3.5.1. Allow appliance to cool down.
3.5.2. Unplug the appliance from the mains power
supply.
3.5.3. Clean the appliance as described in the cleaning
section.
4. Cleaning
4.1. Clean the dust bin: when the dust bin is almost
on max, it is time to empty the dust cylinder. Open the
front cover by unclipping the dust cylinder lock. Take
out the bin and empty it.
4.2. Cleaning the HEPA type lter: once the dust bin is
removed un-clip the top handle to remove the HEPA
type lter. Please do not wash. The HEPA type lter
must be shaken to remove dust particles. This should
be done at least once a month.
4.3. Cleaning the air outlet lter: this is situated at the
back of the vacuum. Un-clip the back cover to remove
the air outlet lter. This should be washed at least
every six months. Allow to dry in the sun at least 24hrs
before using again(Ensure that the air outer lter is
properly dry before use).
NB: Please ensure that the lters are clean before
use. This will prolong the life of the motor.
5. Anomalies and repair
5.1. Take the appliance to an authorised support centre
if product is damaged or other problems arise.
5.2. If the connection to the mains has been damaged,
it must be replaced and you should proceed as you
would in the case of damage.
31100_IM.indd 6 06-Jul-17 11:28:32 AM
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mellerware Vortex - 31100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mellerware Vortex - 31100 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 1.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info