494813
3
Zoom out
Zoom in
Previous page
1/5
Next page
8
CHECK
Check that the other buttons correspond to the functions of the original remote control; if not, it is likely
that the code found is incorrect, but is used for a very similar device. In that case, repeat the procedure
from point 2.
If the manual search for the code is successful, obtain the code in use by following the DISPLAY CODE IN
USE procedure and make a note of it inside the battery cover.
NOTE: During the search the indicator stops ashing and the remote control exits the programming mode
in the following cases:
• if for 12 seconds the button indicated is not pressed or if another button is pressed
if the list of codes to nd is terminated. If this happens, go to the www.meliconi.com/guide website
SETTING CODES USING A MANUAL SEARCH
(only to be performed if the speci c code could not be found)
1. Switch on the device to be programmed:
- if it is a TV, SAT or TER select a programme
- if it is a DVD insert a DVD.
- if it is a VCR insert a cassette
2. Press and hold down for 6 seconds the device selection
button corresponding to the device you wish to enter
the code for. Note: Use the PVR button if the device is a
VCR.
3. Release the button. The indicator light will ash. Point
the remote control at the device and press the ON/OFF
key (or PLAY if it is a VCR/DVD). If the device does NOT
switch off (or if the VCR/DVD does not start playing)
press the same button again slowly (it may be necessary
to press the button several times).
4. When the device responds correctly, press OK. Three
long ashes indicate that the operation has been carried
out correctly.
6 SEC.
or or or or
or
NOTE: If you don’t receive an SMS on your cell phone or if the message says ERROR / NO CODE, it means
the system has not been able to process the data you have sent. Do not try sending another SMS use the
SETTING CODES USING A MANUAL SEARCH procedure instead.
If the device does NOT switch off (or if the VCR/DVD does not start playing), try setting the consecutive code in
the SMS list on the remote control.
When the device reacts check whether the other buttons are operating correctly too.
If they do, the remote control is ready to use.
If they don’t, you are probably using an incorrect code destined for a very similar device; at this point
ignore the SMS list and consult the SETTING CODES USING A MANUAL CODE section to nd a more suitable
code.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Meliconi Pratico 6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Meliconi Pratico 6 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info