494811

Meliconi Gumbody Facile 3 web Manual

5
Zoom out
Zoom in
Previous page
1/7
Next page
12
To acquire signals you must fi rst make sure that the remote controls are the correct distance apart:
At this point the maximum data exchange distance between the two remote controls will have been
reached. To acquire signals the remote controls must now be positioned at half this distance and then not
moved any further until the process has terminated.
1. Position the original remote control in front of the uni-
versal remote control so that the areas which emit the
infrared signals are opposite each other at a distance of
approximately 5 cm.
2. Press the LEARN button for an instant and then, within
fi ve seconds, press and hold down any button on the
original remote control. The green light under the LEARN
button should then start fl ashing. If it doesn’t move the
remote controls closer together.
3. Gradually increase the distance between the two remote
controls, making sure that they stay aligned until the
point at which the green light under the LEARN button
stops fl ashing.
5 cm
Max. dist.
Learning missing functions from an original remote control and saving
them on any button on the Facile 3 web
Important: when you release the button, if the LEARN button light comes on again, press the same button
on the original remote control again until the light goes out once more.
8. If the procedure has been completed successfully the
red light corresponding to the selected device gives
three long fl ashes. Only at this point will the remote
control be ready to capture other signals to be saved on
other buttons.
Having programmed the Facile 3 web, every time you press a button linked to a LEARN command, both
the light corresponding to the device being used and the LEARN button light will come on.
4. Press the selection button for the required device for an
instant.
5. Press the LEARN button for an instant together with
one of the F1 - F2 - F3 - F4 buttons or any other normal
button you wish to save the new function on.
6. The green light on the LEARN button will light up in
steady mode to indicate that it is waiting to receive a
signal from the original remote control.
7. On the original remote control, press the button
corresponding to the signal you wish to capture and hold
it down until the green light on the LEARN button goes
out.
or
or
or
or
or
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Meliconi Gumbody Facile 3 web at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Meliconi Gumbody Facile 3 web in the language / languages: English as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info