This product must not be disposed of together with domestic waste.
hand in all electrical or electronic devices, regardless of whether or not they contain toxic
substances, at a municipal or commercial collection point so that they can be disposed of
in an environmentally acceptable manner
the device. Do not dispose of old batteries with your household waste, but at a battery
Electromagnetic compatibility - Guidance and manufacturer‘s declaration
Effective: 19-Jul-2014
Electromagnetic emissions
The Pulse Oximeter is intended for use in the electromagnetic environment specied below
customer or the user of the device should assure that it is used in such an environment.
Emissions test Compliance Electromagnetic environment
– guidance
RF emissions Group 1
CISPR1
RF emissions Class B
CISPR1
Harmonic emissions
Not applicable
nach IEC 61000-3-2
V
icker emissions Not applicable
IEC 61000-3-3
Electromagnetic immunity
The Pulse Oximeter is intended for use in the electromagnetic environment specied below
customer or the user of the device should assure that it is used in such an environment.
Immunity IEC 60601- Compliance Electromagnetic environment
test test level level – guidance
Electrostatic
discharge (ESD)
IEC 61000-4-2
Power frequency
(50/60 Hz)
magnetic eld
IEC 61000-4-8
Electromagnetic immunity
The Pulse Oximeter is intended for use in the electromagnetic environment specied below
customer or the user of the device should assure that it is used in such an environment.
Immunity IEC 60601- Compliance Electromagnetic environment
test test level level – guidance
Radiated RF
IEC 61000-4-3
The Pulse Oximeter is suitable for use in all
establishments, including domestic establish-
ments and those directly connected to the
public lowvoltage power supply network
that supplies buildings used for domestic
purposes.
The Pulse Oximeter uses RF energy only for
its internal function.
Therefore, its RF emissions are very low and
are not likely to cause any interference in
nearby electronic equipment.
± 6 kV
contact
± 8 kV air
± 6 kV
contact
± 8 kV air
Floors should be wood, concrete or ceramic tile.
If oors are covered with synthetic material, the
relative humidity should be at least 30 %.
3 A/m 3 A/m
Power frequency magnetic elds should
be at levels characteristic of a typical
location in a typical commercial or hospital
environment.
3 V/m
80 MHz to
2,5 GHz
3 V/m
Portable and mobile RF communications
equipment should be used no closer to any
part of the thermometer
than the recommended separation distance
calculated from the equation applicable to
the frequency of the transmitter
Recommended separation distance:
d=1.2 √ P
d=1.2 √ P 80 MHz to 800 MHz
d=2.3 √ P 800 MHz to 2,5 GHz
T
Name and model :
Display system :
Power supply :
Measuring range :
Accuracy :
Display resolution :
Response time :
Life cycle :
Automatic switch-off :
Operating conditions :
Storage conditions :
Dimensions :
Weight :
Article number :
EAN number :
The current version of this instruction manual can be found under
www
W
Please contact your dealer or the service centre in case of a claim under the warranty
to return the unit, please enclose a copy of your receipt and state what the defect is.
The following warranty terms apply:
1. The warranty period for MEDISANA products is three years from date of purchase. In case of
a warranty claim, the date of purchase has to be proven by means of the sales receipt or
invoice.
2. Defects in material or workmanship will be removed free of charge within the warranty period.
3. Repairs under warranty do not extend the warranty period either for the unit or for the
replacement parts.
4. The following is excluded under the warranty:
a.
instructions.
b.
parties.
c. Damage which has arisen during transport from the manufacturer to the consumer or during
transport to the service centre.
d.
5. Liability for direct or indirect consequential losses caused by the unit are excluded even if the
damage to the unit is accepted as a warranty claim.
MEDISANA
E-Mail: info@medisana.de, Internet: www
The service centre address is shown on the attached leaet.
Recommended separation distances between portable and mobile
RF communications equipment and the
Pulse Oximeter
The Pulse Oximeter is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the device can help prevent electro-
magnetic interference by maintaining a minimum distance between portable and mobile RF
communications equipment (transmitters) and the device as recommended below
the maximum output power of the communications equipment.
Rated maximum
output power
of transmitter
W
0.01 0.1
0.1 0.3689 0.7378
1 1.1667 2.3334
10 3.6893 7.3786
100
1
For transmitters rated at a maximum output power not listed above, the recommended separation
distance d in metres (m) can be estimated using the equation applicable to the frequency of the
transmitter
to the transmitter manufacturer
NOTE 1
NOTE 2 These guidelines may not apply in all situations.
Electromagnetic propagation is affected by absorption and reection from structures, objects and
people.
Separation distance according to frequency of transmitter
m
80 MHz to 800 MHz
d=1.2 √ P
800 MHz to 2.5 GHz
d=2.3 √ P
MEDISANA Pulse Oximeter PM 100
Digital display (OLED)
3 V , 2 batteries (type LR03,
SpO
2
: 70 % - 99 %, Pulse: 30 - 235 beats / min.
SpO
2
: ± 2 %, Pulse: (30 - 99) = ± 2; (100 - 235) = ± 2 %
SpO
2
: 1 %, Pulse: 1 beat / min.
ø 12,4 seconds
approx. 5 years (if used for 15 measurements à 10 minutes per day)
After approx. 8 seconds
+5°C - +40°C, max. 80 % rel. humidity
-20°C - +55°C, max. 93 % rel. humidity
approx. 58 x 34 x 35 mm
approx. 53 g
79455
40 15588 79455 1
In accordance with our policy of continual product improvement, we reserve the right
to make technical and optical changes without notice.
0297
GB Instruction manual Pulse Oximeter PM 100
Thank you very much for your condence in us and congratulations on your purchase!
YMEDISANA quality product with your purchase.
long-term satisfaction with your MEDISANA Pulse Oximeter PM 100 , we recommend that you read
the following operating and maintenance instructions carefully
IMPORT
RET
Read
safety instructions, and keep the instruction manual for future use.
Should you give
these instructions for use.
Explanation of symbols
This instruction manual belongs to this device. It contains important
information about starting up and operation. Read the instruction
manual
in serious injury or damage to the device.
W
These warning notes must be observed to prevent any injury to the
user
CAUTION
These notes must be observed to prevent any damage to the
device.
NOTE
These notes give
or operation.
The degree of protection against dripping water
Classication: T
2
alarm
Lot number Storage conditions
Manufacturer Serial number
Date of manufacture
IPX1
ASSIGNED PURPOSE
The Pulse Oximeter PM 100 is a portable non-invasive device intended for spot-
checking
adult and pediatric patients. It is not suitable for continuous monitoring.
SAFETY INFORMA
•
•
•
•
•
•
Pulse oximeters are sensitive to motion artefacts. Therefore keep hands still while taking a reading.
Pulse
you have poor circulation, warm your hands by rubbing them together or use another method befo-
re attempting
may also result in inaccurate readings.
Fingernail -
accurate readings.
Y
If a reading is different to obtain, switch to another nger or to the other hand.
Inaccurate measurement results may also caused by:
- dysfunctional hemoglobin or low hemoglobin
- the use of intravascular dyes
- high ambient light
- excessive patient movement
- high-frequency electrosurgical interference and debrillators
- venous pulsations
0297
1
2
3
4
•
•
•
•
•
•
•
•
•
•
•
•
•
•
SAFETY NOTES FOR BA
•
•
•
•
•
•
•
•
•
•
•
Items supplied and packaging
Please check
not use it and contact the service centre. The following parts are included:
• 1 MEDISANA
• 2 Batteries (type
• 1 Lanyard
• 1 Instruction manual
The packaging can be reused or recycled. Please dispose properly of any packaging material no
longer required. If you notice any transport damage during unpacking, please contact your dealer
without delay
Device and controls
1
OLED Screen
2
Start-button
3
Opening for nger
4
Battery compartment lid (on rear side of the device)
Insert / change battery
Insertion: Y
compartment
4
is located on the backside of the unit. Open it, remove it and insert the 2 x
type 1.5 V batteries supplied. Ensure correct polarity when inserting (as marked inside the battery
compartment). Close the battery compartment.
Removal: Replace the batteries when the battery exchange symbol appears in the display
If nothing is displayed the batteries are completely empty and need to be replaced immediately
Use
1.
2.
3.
4.
5.
6.
What does the measured result mean?
The oxygen saturation (SpO
2
) of the blood is a term referring to the concentration of oxygen at-
tached to human hemoglobin. The normal value lies between 90 and 96 % SpO
2
.
may be an indication for existing diseases like e.g. cardiac defect, problems of the circulatory sys-
tem, asthma or specic diseases of the lung.
deep breathing, what bears the danger of a too low blood carbon dioxide level. The value measured
with
all circumstances to get a correct diagnosis.
- placement of a sensor on an extremity with a blood pressure cuff, arterial catheter
vascular line
- patients suffering from hypotension, severe vasoconstriction, severe anemia, or hypothermia
- cardiac arrest or shock
- false ngernails
- circulatory disorder
The Pulse Oximeter will not alert you if your readings are out of normal range.
Explosion hazard: Do not use the Pulse Oximeter in an explosive atmosphere.
The device is not suitable for continuous blood oxygen monitoring.
In order to ensure correct sensor alignment and skin integrity
single site for our device should be less than 4 fours.
Operation of the Pulse Oximeter may be affected by the use of an electrosurgical unit (ESU).
Do not use the Pulse Oximeter in an MRI or CT environment.
The Pulse Oximeter is intended only as an adjunct in patient assessment. It must be used in con-
junction with other methods of assessing clinical signs and symptoms advised by a professional
physician.
The device is not intended for sterilization or for cleaning with liquids.
This equipment is not intended for use during patient transport outside the healthcare facility
This equipment should not be used adjacent to or stacked with other equipment.
The device must not be used with accessories, detachable parts and other materials not described
in the instructions for use.
Please do not attempt to repair the unit yourself in the event of malfunctions. Stop using the device
and conact the service centre.
The materials that contact with the patient’s skin have been tested to be in tolerance. In case you
should detect skin irritations etc., stop using the device and contact a doctor
The swallowing of small parts like packaging bag, battery
suffocation.
W
Please ensure that the polythene packing is kept away from the
reach of children! Risk of suffocation!
Do not disassemble batteries!
Never leave any low battery in the battery compartment since it may leak and cause damage to
the unit!
Increased risk of leakage!
If battery acid comes in contact with any of these parts, rinse the affected area with copious
amounts of fresh water and seek medical attention immediately!
If a battery has been swallowed, seek medical attention immediately!
Insert the batteries correctly
Keep batteries out of children‘s reach!
Do not attempt to recharge batteries! There is a danger of explosion!
Do not short circuit! There is a danger of explosion!
Do not throw into a re! There is a danger of explosion!
Do not throw used batteries into the household refuse; put them in a hazardous waste container or
take them to a battery collection point, at the shop where they were purchased
Oxygen
saturation in %
Pulse frequency
Pulse Signal Start-button
Open the nger opening by pressing the left upper and lower parts of the device together
Place
3
on the right side of the device and release
the upper and lower parts.
Press the Start-button
2
. The OLED-screen will switch on immediately
Keep your nger resp. your whole body still for the reading.
After a short time, the values for the pulse frequency and the blood oxygen saturation appear on
the OLED screen:
By repeatedly pressing the Start-button
2
you may switch between 6 different display modes
(showing the already explained values in different view modes).
Remove your nger
Adjustement of the display brightness
The MEDISANA Pulse Oximeter PM 100 of-
play in 10 steps. T
2
(device must be switched on), until
the desired brightness level is reached. The current brightness level is displayed on the upper right
screen area (e.g. Br 1 , Br 2 , Br 3 , Br 4 etc.). The factory setting is level 4 (Br 4 ).
Using the Lanyard
AMEDISANA
Pulse Oximeter PM 100. Y
threading the thinner end of the lanyard through the hanging hole
on the left side of the device.
T
Error: SpO
2
and / or pulse frequency values are not displayed resp. are not displayed correctly
Remedying: Place on of your ngers completely into the nger opening
3
on the backside of the
device. Use a new battery
can be measured, contact the service centre.
Error: The device cannot be switched on.
Remedying: Remove the old battery and insert a new one. Press the ST
2
. If the
device still cannot be switched on, contact the service centre.
Error: „Error 3 “ or „Error 4 “ appear on the display
Remedying: Replace the batteries. -
not be eradicated by replacement of the batteries. Contact the service centre.
Error: „Error 6 “ or „Error 7 “ appear on the display
Remedying: The LED screen is defective or another technical error is present. Does the error
message still appear even after you have exchanged the batteries, contact the service centre.
Cleaning and maintenance
Remove the batteries before cleaning. Never use strong detergents or hard brushes. Clean the unit
with a soft cloth, moistened with isopropyl alcohol. Do not let water enter the unit.
only use the unit when it is completely dry
Disposal
collection station at a recycling site or in a shop. Consult your municipal authority or your dealer for
information about disposal.
Directives / Norms
This
symbol) “CE 0297”. The
14 June 1993 concerning medical devices” are met.
Electromagnetic The device complies with the EN 60601-1-2 standard for elec-
tromagnetic compatibility
NOTE 1
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reection from structures, objects and people.
a. Field strengths from xed transmitters, such as base stations for radio (cellular/cordless) telephones
and land mobile radios, amateur radio,
theoretically accuracy T assess the electromagnetic environment xed RF transmitters, an
electromagnetic site survey should be considered. If the measured eld strength in the location in which the
device is used exceeds the applicable RF compliance level above, the device should be observed to verify
normal operation. If abnormal performance is observed, additional measures may be necessary
reorienting or relocating the device.
b. Over the frequency range 150 kHz to 80 MHz, eld strengths should be less than 3 V/m.
where P is the maximum output power rating
of the transmitter in watts (W) according to
the transmitter manufacturer and d is the
recommended separation distance in metres
(m). Field strengths from xed RF transmit-
ters, as determined by an electromagnetic
site survey
a
, should be less than the compli-
ance level in each frequency range
b
. Interfe-
rence may occur in the vicinity of equipment
marked with the following symbol:
