743061

Medisana CR 870 Manual

5
Zoom out
Zoom in
Previous page
1/22
Next page
5
Inserting the batteries
1. Open the battery compartment on the underside
of the device.
2. Insert batteries observing the polarity signs
(+ and -) inside the battery compartment.
NOTE: The batteries are stacked with one of the
batteries behind the other two.
3. Close the battery compartment.
How to use
1. Ensure that your feet are clean and dry.
2. Use the switch to select a power setting;
For sensitive skin, or softer skin use the LO
setting.
For harder skin use the HI setting.
3. Using light pressure place the surface of roller
onto the heel or sole of your foot and gradually
move the device around to target areas of hard
skin. Do not use on a single area for more than 4
seconds at a time.
4. Check the results throughout. Once you are happy
with the results turn the switch to OFF.
5. Rinse your feet with clean water & dry before
applying your favourite foot cream.
Cautions
Before use, make sure that the roller is in good condition. Any malformation,
distortion or damage may cause skin injury.
DO NOT APPLY EXCESS PRESSURE OR CAUSE THE MOTOR TO STOP ROTATING. FOR
BEST RESULTS, RUN THE UNIT GENTLY OVER THE SKIN. THIS WILL ENSURE SOFT,
SAFE AND SMOOTH REMOVAL OF DEAD SKIN.
INSTRUCTIONS FOR USE:
PRODUCT FEATURES
Main body
Power switch
3x AAA batteries
Changing the rollers
To remove the roller.
1. Ensure the switch is in the OFF position.
2. With one hand press the release button on the
side of the device.
3. With the other hand lift out the roller. TIP: It’s
easier to lift the roller out from the end closest to
the release button.
To insert a new roller.
1. Loosely position one of the roller pins into the recess on the end furthest from
the release button.
2. Push the other end of the roller into place using the groves to guide it into
position.
3. The roller will secure into place with a click.
MAINTENANCE AND STORAGE
• Always turn the device o before cleaning it.
• Only clean the device with the supplied brush or a dry cloth. Do not use
chemical agents including benzene, alcohol etc.
• Remove batteries if equipment is not going to be used for extended periods
of time, and store batteries in a cool dry place away from direct sunlight and
metal objects.
• If motor power seems reduced, replace the batteries.
• If roller surface becomes worn or less abrasive, t a new roller.
SERVICE
CR 870 - Article No: 88576 / EAN Code: 40 15588 88576 1
Coarse roller:
blue edge
Cleaning brush
Extra coarse roller:
white edge
Release button
Fine roller: grey edge
(where supplied)
GB
The service centre address is shown on the attached leaet.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Medisana CR 870 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Medisana CR 870 in the language / languages: German, Dutch, French, Italian, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info