459673
33
Zoom out
Zoom in
Previous page
1/143
Next page
4
Programming device codes
General
For every device that you would like to operate using the uni
versal remote control, you must program a threedigit de
vice code to a source key (
TV, VCR, DVD, ASAT, DSAT,
CBL, CD, AUX
) . You can assign any key to any device
(“Flex Mode”), with exception of the
TV
key which can only
be assigned to a TV.
Combined devices (e.g. TV set with video recorder): It is
often necessary to assign two source keys with the respec
tive code for each part of the device. However, there are also
combined devices with only one code for both device parts
(see also “Operating combined devices”, page 7).
VCR’s: The code search for VCR's must be done while a
tape is inserted.
Preprogramming
The remote control has been preprogrammed for several
devices produced by Medion. Because of this you can use
certain basic functions for, for example, a Medion television
directly and without having to programme in the device
code.
Entering the device code according to the
Code List
The codes of the corresponding devices can be found in the
Code List enclosed with these operating instructions. Pro
ceed as follows:
1. Switch the relevant device on manually.
2. Keep the
SETUP
key pressed down for approx. 3
seconds, the background lighting of the source key will
flash for a short time and then remain permanently lit.
1
(Briefly pressing the
SETUP
key will activate the SHIFT
function.)
3. Briefly press the desired source key (
TV, VCR, DVD,
ASAT, DSAT, CBL, CD, AUX
).
4. Enter the threedigit code from the Code Table.
The background lighting will extinguish briefly each
time the key is pressed.
If the entered code was valid, the light of the source
key will extinguish after the last digit has been en
tered. If an invalid code was entered, the source key
will flash for three seconds before extinguishing.
If the device does not respond as expected, repeat the pro
gramming, or try a different code. Please try all the codes
specified for your brand. Select the code that causes all the
available commands of your remote control to respond cor
rectly.
If this is not successful either, then try using the search me
thod described in the chapter "Automatic Search".
1. Only the source key that was actuated last will light
up. During first use, the TV key will light up.
Keypad backlight: Press the key to turn the keypad
backlighting on or off. – Please note that the keypad back
lighting is only visible in a dark environment.
URC MD 81035 ML.book Seite 4 Mittwoch, 8. Februar 2006 12:35 12
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Medion MD81035 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Medion MD81035 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 5,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Medion MD81035

Medion MD81035 Additional guide - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info