568580

ME VD 6710 Manual

16
Zoom out
Zoom in
Previous page
1/40
Next page
VISTUS-VD | ENGLISH
16
enough hold then drill more holes and use them to also screw the
indoor station in place.
3. Drill the attachment holes with a 6 mm drill and insert one dowel in
each hole.
4. Feed the lines through the feed hole in the lower casing part
designed for this purpose and screw this down.
5. Attach the lines in accordance with the wiring plan and replace the
front casing section onto the lower casing section. Make sure that it
clicks correctly into place.
CONNECTION
An exact description of where the individual connections and terminals
are located can be found in the figures. The recommended wiring can be
seen in the corresponding wiring plan in the affix.
Connect the lines to the audio, +15V, GND and video on the outdoor
station. These terminals are also present on the indoor stations and need
to be connected to one another 1:1.
Note on the 2-family versions: One four-pole connection terminal is
present in each residential unit. The connection terminals are numbered.
Connection terminal 1 is for the lower and connection terminal 2 is for
the upper bell button.
Connecting the door opener
The door opener is connected directly to the outdoor station with two
lines (Figure A ‚Door opener‘). No additional power supply is necessary
in order to control the door opener. The door opener must be designed
for 12 volt DC voltage and may not require more than 1A of power. In
the event that the door opener needs to be correctly polarised then both
connection terminals must be marked ‘lock +’ and ‘lock –‘.
Note: In order to prevent a door opening by tampering of the outdoor
station, we recommend the installation of the separately available
security door opener module SDO-10, which is mounted in the service
entrance box. The SDO-10 is also suitable for motor locking systems and
offers several adjustable door opening times and an
auto-door-open function.
Connecting the power supply
The power supply can be connected to either the indoor or the outdoor
station. Separate spring clips are present for this purpose.
It is also possible to connect the power supply directly to the signal line
e.g. from the fuse box to the outdoor and indoor units. The power supply
unit then needs to be connection with the ground (GND) and +15V.
Open power supply unit can supply up to 8 units with power.
Connecting the external camera
An external camera can be connected to the spring clips (Figure A ‚ext
Cam‘), for example in order to be able to monitor an additional area
that is not visible on the main camera. All cameras can be connected
that require a supply voltage of 12 Volt DC and supply
an FBAS video signal.
The video line is connected to the terminal (V2) and the ground line
is connected to the terminal (GND); the supply voltage for the camera
is taken from the terminals ‘VCC2’ (positive terminal) and ‘GND’
(negative terminal).
The external camera automatically receives ID 4 (see chapter on the ID
code). When the external camera is active it is not possible to transmit
sound. The X-module on the VDV 500 XCam is not required.
Connecting a floor button
Any floor button that is present (normal closing contact) is connected
to the terminals ‘floor button’ on the indoor unit. Alternative the button
can also be connected in parallel to the lines ‘audio’ and ‘GND’. On
the two-family version please note that the correct audio line is used
(Audio1 and GND for fam. 1 and Audio2 and GND for fam. 2).
Note: If a floor button is connected then an unchangeable ring tone
is played when the floor button is activated. This ring tone is fixed
and is not included in the ‘normal’ tones/melodies to make it easy to
differentiate.
Connecting the wireless expansion model VTX-BELL
The VTX-BELL can be used to send the bell signal wirelessly to the
receiver in the BELL series (currently BELL 200 RX, BELL 210 USB and
BELL 220 RX). The wireless module will be attached to the 3-pole plug
inside the indoor station (Figures B+C). For more information please
see the VTX-BELL instructions.
POSSIBLE SETTINGS ON THE OUTDOOR STATION
The outdoor station has the following possibilities of adjusting the
system to your personal circumstances:
Volume on the outdoor station
The potentiometer (Figure A ‚Volume / Lautstärke‘) is used to set
the speaking volume on the outdoor station. For full volume turn the
potentiometer carefully in a clockwise connection until it stops and turn
it back a little. Turning the potentiometer in an anti-clockwise direction
reduces the volume.
ID code
If several outdoor stations are used in parallel (e.g. on the gate and
on the house), the DIP switch is used to set the ID code (Figure A,
VISTUS VD-600_I-Manual_210x240_Fin9.indd 16 10.06.13 15:52
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ME VD 6710 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ME VD 6710 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info