568583

ME VD 607 Manual

17
Zoom out
Zoom in
Previous page
1/40
Next page
ENGLISH | VISTUS-VD
1717
‚ID-CODE‘). This makes it possible to activate the individual outdoor
stations in turn from one indoor unit in order to be able to monitor the
scope of the corresponding outdoor units. The switch is activated on the
indoor station with the ‘monitor’ button.
ID1 = Switch 1 ‘on’, Switch 2 ‘on’
ID2 = Switch 1 ‘on’, Switch 2 ‘off’
ID3 = Switch 1 ‘off’, Switch 2 ‘on’
Note: ID 4 is not available for the outdoor station. It is reserved for the
outdoor camera. If several outdoor stations are used in parallel then
only one outdoor station can be connected to the external camera.
Door opener time
The DIP switch (Figure A, ‚Door opener time‘) is used to set how long
the door opener should be activated for. The possible settings are 1
second or 5 seconds. 5 seconds is the factory setting and works for
most standard door openers.
Switch ‘off’ corresponds to an opening time of 1 second.
Switch ‘on’ corresponds to an opening time of 5 seconds.
POSSIBLE SETTINGS ON THE INDOOR STATION
The following settings are possible on the indoor station to adjust the
system to your personal circumstances:
Ring tone volume (3.5“ and 7“ monitor)
The potentiometer (Figure B and C ‘Bell Volume‘’) is used to set the
ring/volume on the indoor station. For full volume turn the potenti-
ometer carefully in a clockwise connection until it stops. Turning the
potentiometer in an anti-clockwise direction reduces the volume.
Deactivate ring tone/melody (e.g. during the night)
The ring tone/melody can be deactivated, e.g. in order to prevent
disturbance during the night. Either press the mute button on the
indoor unit once briefly. The LED below the mute button lights up red
as a reminder that the melody is deactivated. To activate the melody
again press the mute button again briefly. When the red LED goes out
the melody has been re-activated.
The optical signal (surround light on the talk and door opener button)
remains active, even then the ring tone/melody is deactivated and still
rings. The red LED flashes if the bell is rung while the mute is activated.
NOTE: If the VTX-BELL module is used then this will also be deactivated
in the silent mode, i.e. the connected receivers will not give a
signal either.
IMPORTANT: The monitor on the indoor station needs to be
activated for the following settings (e.g. by pressing the screen button).
Otherwise it is not possible to set the talk/volume, brightness, contrast,
colour saturation and melody.
Speaking volume (3.5“ and 7“ monitor)
The two side buttons (B/C. 12 and 13) can be used to set the speaking
volume in several steps. Button 12 is used to increase the volume and
button 13 to reduce it.
Brightness (3.5“ monitor)
The
button (B.8) is used to set the brightness on the monitor. The
button is pressed multiple times to increase the brightness. Once the
highest level of brightness has been reached another press will switch it
to the lowest level of brightness.
Contrast (3.5“ monitor)
The button (B.9) is used to set the contrast on the monitor. The
button is pressed multiple times to increase the contrast. Once the
highest level of contrast has been reached another press will switch it to
the lowest level of contrast.
Colour saturation (3.5“ Monitor)
The button (B.10) is used to set the colour saturation on the monitor.
The button is pressed multiple times to increase the saturation. Once
the highest level of saturation has been reached another press will
switch it to the lowest level of saturation.
Brightness (7“ monitor)
Press the button (C.8) on the indoor station once and the OSD will
display ‘Bright’. You can now increase the brightness using button (C.9)
and reduce it using button (C.10).
Contrast (7“ monitor)
Press the button (C.8) on the indoor station twice and the OSD will
display ‘Contrast’. You can now increase the contrast using button (C.9)
and reduce it using button (C.10).
Colour saturation (7“ monitor)
Press the button (C.8) on the indoor station three times and the
OSD will display ‘Colour’. You can now increase the colour saturation
using button (C.9) and reduce it using button (C.10).
Melody selection (3.5“ and 7“ monitor)
The next melody is played every time you press the button
(B/C.11). The last melody to be played is automatically stored.
VISTUS VD-600_I-Manual_210x240_Fin9.indd 17 10.06.13 15:52
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ME VD 607 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ME VD 607 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info