Manual ME ADV-F10 (page 11 of 28) (English, German, Dutch, French)

568514

Zoom out

Zoom in

1/28

ENGLISH | ADV-F10

1. The DECT power box must be opened before installation. No tools

are required as the casing is only clicked together. Simple press the

tab on the bottom inwards slightly and then lift the casing lid off

the box as shown in ﬁgure A1.

2. Hold the back section with one hand and mark the holes with a

suitable pen.

3. Lay the back section to one side and drill the holes

with a 6 mm drill.

4. Insert the included dowels into the holes and screw the back

section on.

5. Connect the antenna to the power box. It has a screw connection

for this purpose.

NOTE: To optimize the range, you can place the antenna at a different

location using a separately available antenna extension.

DECT indoor station

The DECT indoor station is installed in ﬁxed position using four installa-

tion holes in the corners. The power supply is fed into the casing from

behind. Ensure correct polarity when connecting the power supply.

1. The DECT indoor station must be opened before installation. As this

casing is also only clicked together, no tools are necessary here

either. Simply press the tab on the bottom inwards slightly and

then lift the casing lid off the box as shown in ﬁgure B1.

Take care not to rip off the wires for the loudspeaker and

the microphone.

2. A drilling template is included to drill the corresponding holes to

attach the DECT indoor station. Then, align this at the installation

location, using a spirit level if necessary, and stick it to the wall

with tape.

3. Drill the holes with a 6mm drill.

4. Insert the included dowels into the holes and screw the back

section on.

Ensure that you feed the cable for the power supply to the DECT

indoor station into the casing beforehand.

OPERATION

You can connect the power once all components have been installed,

ﬁrst at the outdoor station and the DECT power box and then at the

DECT indoor station.

The red power LED (4a) should then light up on the DECT power box.

On the DECT indoor station, the status LED (20) should ﬁrst ﬂash

alternately red/blue and then light permanently after a short time. The

system is then ready for operation and the bell can be activated at the

outdoor station.

Procedure

1. Press the bell button on the outdoor station

2. The blue LED (4b) on the DECT power box ﬂashes and the indoor

station(s) play(s) the set ring melody.

3. Within 60 seconds, the press to talk button (17) can be pressed

and a conversation held with the visitor. All other indoor stations

immediately stop ringing.

4. Any door opener that is connected to the outdoor station can be

activated during the conversation by pressing the door opener

button (19).

5. To end the conversation, press the press to talk button once (17).

Note: after approximately 60 seconds, the DECT indoor station

automatically switches back to standby mode.

Set the ring melody

To hear the programmed ring tone, you can simply ring from the

outdoor station.

1. Press the button (10) to hear the next ring tone.

2. Once the tone that you wish to use is played, wait 10 seconds. The

ring tone is then programmed.

Set the volume of the ring melody

1. Open the indoor station by pressing the bottom tab on the casing a

little and pull the front casing forwards, as shown in the illustraton.

2. The volume of the ring tone is set using the potentiometer (8) on

the circuit board. Turn it in a clockwise direction to increase the

volume and in an anti-clockwise direction to reduce the volume.

NOTE: Ensure that you do not overwind the potentiometer. It can only

be turned by approx. 320°.

Deactivating the ring tone

Use the button (16) below the loudspeaker to set the ring melody to

silent, for example, so that you are not disturbed during your lunch

break. The LED under the button (21) lights up red if the ring melody

is deactivated.

Set the conversation volume on the indoor station

The potentiometer (9) on the side can be used to set the conversation

volume to any level. Turn the wheel upwards to increase the volume

and downwards to reduce it.

Alarm button

If the alarm button (11) is pressed during a conversation with the

outdoor station, then an alarm will sound at the outdoor station.

This button is without function if there is no connection to the

outdoor station.

ADV-F10_I-Manual_210x240_fin7.indd 11 12.11.13 16:57

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ME ADV-F10 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ME ADV-F10 Manual

Product: