Manual ME AD 4020 (page 17 of 36) (English, German, Dutch, French)

568585

Zoom out

Zoom in

1/36

ENGLISH | VISTUS-AD

1717

Deactivate ring tone/melody (e.g. during the night)

The ring tone/melody can be deactivated, e.g. in order to prevent

disturbance during the night. Either press the mute button on the

indoor unit once brieﬂy. The LED below the mute button lights up red

as a reminder that the melody is deactivated. To activate the melody

again press the mute button again brieﬂy. When the red LED goes out

the melody has been re-activated.

The optical signal (surround light on the talk and door opener button)

remains active, even then the ring tone/melody is deactivated and still

rings. The red LED ﬂashes if the bell is rung while the mute is activated.

NOTE: If the VTX-BELL module is used then this will also be deactivated

in the silent mode, i.e. the connected receivers will not give a

signal either.

IMPORTANT: The indoor station needs to be activated for the

following settings (e.g. by pressing the talk button). Otherwise it is not

possible to set the talk/volume, and melody.

Speaking volume

The two side buttons (B. 12 and 13) can be used to set the speaking

volume in several steps. Button 12 is used to increase the volume and

button 13 to reduce it.

Melody selection

The next melody is played every time you press the button

(B/C.11). The last melody to be played is automatically stored.

OPERATION (as door intercom system)

1. Press the bell button.

2. The stored ring tone will play on the corresponding indoor

station(s)

3. Accept the conversation on the indoor unit by pressing brieﬂy on

the talk button ( ).

4. If a door opener is connection then you can activate it by brieﬂy

pressing the door opener button ( ). The bell button will light

green for the duration of the door opener as conﬁrmation.

5. Press the talk button ( ) brieﬂy in order to switch the system

back to standby operation.

Note: If a ﬂoor button is connected then an unchangeable ring tone

is played when the ﬂoor button is activated. This ring tone is ﬁxed

and is not included in the ‘normal’ tones/melodies to make it easy to

differentiate.

OPERATION (as internal house intercom)

All indoor units that are connected to the same bell button can also be

used as an internal intercom.

1. Press the internal button (B. 7) on the indoor station from

which you wish to reach another indoor station. All the connected

indoor station will ring. No image will be shown.

2. To accept the conversation on one of the other connected indoor

stations you need to brieﬂy press the talk button there (B. 6).

3. The talk button needs to be pressed brieﬂy on one of the two

indoor stations in order to end the conversation.

Note: It is not possible to set different ring tones for internal and

external calls.

Technical data:

Outdoor station

Operating voltage: 15V DC

Standby power: <0.5W

Connection for door opener:

12V DC, max. 0.9 A

Bell button illumination: automatic via CDS sensor

Indoor station

Operating voltage: 15V DC

Standby power: <0.5W

NOTES

The functionality of the unit can be affected by the inﬂuence of strong

static, electrical or high frequency ﬁelds (discharging, mobile phones,

radios, microwaves).

Cleaning and maintenance

Always disconnect mains powered units from the mains supply before

cleaning (disconnect the plug). The unit housing can be cleaned using

a soapy soft cloth. Do not use any abrasive materials or chemicals.

Remove dust build-up from ventilation slits using a brush and clean up

using a vacuum cleaner. Do not hold the vacuum cleaner nozzle directly

against the unit.

SAFETY INSTRUCTION

In the event of damage to the housing, connectors, power cables or

isolation shielding, switch off the device immediately and disconnect

VISTUS AD-400_I-Manual_210x240_Fin8-1.indd 17 13.06.13 15:30

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ME AD 4020 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ME AD 4020 Manual

Product: