Manual ME AD 400 (page 15 of 36) (English, German, Dutch, French)

568587

Zoom out

Zoom in

1/36

ENGLISH | VISTUS-AD

1. Remove the two screws in order to be able to open the casing

on the outdoor station. The casing is also ﬁtted with notches and

projections that connect the upper and lower parts of the casing.

Thus a certain amount of force is necessary in order to separate the

casing parts.

2. Position the drilling template for the outdoor station in a level

location at the intended assembly location (a spirit level is helpful

for this) and attach it with sticky tape.

3. Use the drilling template to drill the attachment holes with a 6mm

drill and insert a dowel into each hole.

4. Now remove the drilling template.

5. Feed the lines through the large hole in the outdoor station and

secure them with 4 screws.

6. Connect the line in accordance with the wiring plan.

Adjusting the nameplate

The nameplate comprises two transparent plastic parts that are

connected with 2 or 4 small screws.

7. Remove all screws from the nameplate and take the plate apart.

The foil for the name can be found between the plastic parts.

8. Write on the foil with a smudge proof felt tip pen or print a

nameplate* using a PC and printer.

9. Lay the complete nameplate (foil) between the two plastic parts

and screw them back together.

* Size of the nameplate:

VISTUS AD-4010: 71 mm x 50 mm

VISTUS AD-4020: 71 mm x 25 mm

VISTUS AD-4030: 71 mm x 15mm

10. Replace the nameplate in the front cover before re-attaching

the front cover to the outdoor station. You can attach a strip of

sticky tape over the nameplate and the casing to ensure that the

nameplate does not fall out during assembly.

Note: Remove the sticky tape from the casing immediately following

installation in order to prevent damage to the front cover!

11. Screw the front cover on using both casing screws. Please ensure

that the screws are not tilted as this can damage the thread in the

lower section of the casing.

ASSEMBLY OF THE INDOOR STATION

The installation height of the Indoor stations can be selected freely

according to your circumstances.

1. The casing on the indoor station is kept together with notches and

projections. To separate the lower section from the front section,

press a small slotted screwdriver against the snap fastener (B.15)

on the bottom side.

2. Use the lower section of the casing as an aid to mark the drill

holes. Make sure that you hold the lower section in a horizontal

position for this step.

NOTE: The lower casing section on the indoor station can also be

attached to a hollow wall box. The corresponding attachment holes

are located around the line feed hole. If this does not provide

enough hold then drill more holes and use them to also screw the

indoor station in place.

3. Drill the attachment holes with a 6 mm drill and insert one dowel

in each hole.

4. Feed the lines through the feed hole in the lower casing part

designed for this purpose and screw this down.

5. Attach the lines in accordance with the wiring plan and replace the

front casing section onto the lower casing section. Make sure that

it clicks correctly into place.

CONNECTION

An exact description of where the individual connections and terminals

are located can be found in the ﬁgures. The recommended wiring can

be seen in the corresponding wiring plan in the afﬁx.

Connect the lines to the audio, +15V and GND on the outdoor station.

These terminals are also present on the indoor stations and need to be

connected to one another 1:1.

Note on the 2-family version: One four-pole connection terminal

is present in each residential unit. The connection terminals are numbe-

red. Connection terminal 1 is for the lower and connection terminal

2 is for the upper bell button.

Note on the 3-family version: One four-pole connection terminal

is present in each residential unit. The connection terminals are numbe-

red. Connection terminal 1 is for the lower, connection terminal 2 is for

the middle and connection terminal 3 is for the upper bell button.

Connecting the door opener

The door opener is connected directly to the outdoor station with two

lines (Figure A ‚Door opener‘). No additional power supply is necessary

in order to control the door opener. The door opener must be designed

for 12 volt DC voltage and may not require more than 0.9A of power.

In the event that the door opener needs to be correctly polarised then

both connection terminals must be marked ‘lock +’ and ‘lock –‘.

VISTUS AD-400_I-Manual_210x240_Fin8-1.indd 15 13.06.13 15:30

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ME AD 400 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ME AD 400 Manual

Product: