643410
69
Zoom out
Zoom in
Previous page
1/74
Next page
6-SICUREZZE E ALLARMI
67
11-PROBLEMS/CAUSES/SOLUTIONS
Technical Dept. - All rights reserved - Reproduction is prohibited
ATTENTION!
All repairs must only be carried out by a specialised technician, with the product switched o and the plug
disconnected.
If the product is NOT used as described in this manual, the manufacturer declines all liability for any damage caused
to persons and property.
All the necessary measures and/or precautions must be adopted when performing maintenance, cleaning and
repairs.
Do not tamper with the safety devices.
Do not remove the safety devices.
Connect the product to an ecient smoke expulsion system.
Verify that the room in which the appliance will be installed is adequately ventilated.
ANOMALY POSSIBLE CAUSES SOLUTIONS
Pellets are not being fed into the
combustion chamber.
The pellet hopper is empty. Fill the hopper with pellets.
Sawdust has blocked the feed screw. Empty the hopper and remove the sawdust
from the feed screw by hand.
Faulty gear motor. Replace the gear motor.
Faulty electronic board. Replace the circuit board.
The re goes out or the appliance
stops automatically.
The pellet hopper is empty. Fill the hopper with pellets.
The pellets are not fed. See the previous anomaly.
The pellet temperature safety probe has
been triggered.
Let the product cool down, restore the
thermostat until the problem is resolved
and switch the product back on. If the
problem persists contact Technical
Assistance.
The door is not closed properly or the
gaskets are worn.
Close the door and replace the gaskets
with original ones.
Unsuitable pellets. Change the type of pellets with those
recommended by the manufacturer.
Low pellet supply. Have the fuel ow rate checked by
Technical Assistance.
The combustion chamber is dirty. Clean the combustion chamber in
accordance with the installation guide.
Clogged outlet. Clean the smoke duct.
Faulty smoke extraction motor. Check the motor and replace it, if
necessary.
Water tank temperature too high. Check the circulation pump is working
properly and eventually replace the
component.
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MCZ Vivo 80 Pellet Hydro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MCZ Vivo 80 Pellet Hydro in the language / languages: English as an attachment in your email.

The manual is 12,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MCZ Vivo 80 Pellet Hydro

MCZ Vivo 80 Pellet Hydro Usermanual and installation guide - Dutch - 64 pages

MCZ Vivo 80 Pellet Hydro Usermanual and installation guide - French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info