643410
65
Zoom out
Zoom in
Previous page
1/74
Next page
63
10-MAINTENANCE AND CLEANING
Technical Dept. - All rights reserved - Reproduction is prohibited
CLEANING THE GLASS
It is recommended to clean the ceramic glass with a dry brush, or if it is very dirty, spray a little specic detergent and clean with a cloth.
ATTENTION!
Do not use abrasive products and do not spray the glass spray cleaner on the painted parts or the door gaskets
(ceramic bre cord).
PERIODIC CLEANING PERFORMED BY A QUALIFIED TECHNICIAN
PULLING THE PRODUCT OUT
Part of the product must be extracted from its seat for maintenance to be performed on certain devices and to clean certain parts. The
mobile part is tted on sliding guides, which facilitate the handling process. The compensation frame must be removed by following the
instructions in this manual before pulling the product out in order to prevent any damage during maintenance. The two lower front screws
must be removed from the product in order to pull it out.
Once the screws are removed, simply exert slight force towards you to pull the mobile part like a drawer. The guides have an end-of-travel
that block the mobile part when extracted completely.
ATTENTION: THE PRODUCT MUST ONLY BE PULLED OUT WHEN COLD AND THE POWER SUPPLY MUST BE DISCONNECTED
IN ADVANCE.
When the mobile part is set back in place, make sure the two screws removed previously are tightened well. The
product may not work if the above is not done, due to no power supply or leaking soot.
CLEANING THE HEAT EXCHANGER
The compartment through which the exhaust smoke passes must be cleaned at the end of the winter season.
This cleaning process is mandatory in order to facilitate the general removal of all combustion residue, before it becomes very dicult to
remove it due to the humidity compacting it over time.
If necessary, clean it more often.
It is good practice to guarantee eective ventilation in the room while cleaning the product.
When the appliance is cold clean the walls of the steel rebox, especially the rear panel, with a scraper (supplied), in order to get rid of
the incrustations caused by soot. Incrustations act as insulation and the thicker they are, the less heat is transmitted to water and to the
structure in general.
Also clean the exchanger pipes going into the four holes at the top (two on the left and two on the right inside the replace) with the
swab brush (supplied).
To nish cleaning, at this point, empty the brazier and the ash pan; in order to get rid of the soot removed in the previous operations one
must also empty the extractable drawer which is located under the ash pan.
To pull out the drawer one must remove the three screws.
Reassemble everything following the operations described above in reverse order.
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MCZ Vivo 80 Pellet Hydro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MCZ Vivo 80 Pellet Hydro in the language / languages: English as an attachment in your email.

The manual is 12,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MCZ Vivo 80 Pellet Hydro

MCZ Vivo 80 Pellet Hydro Usermanual and installation guide - Dutch - 64 pages

MCZ Vivo 80 Pellet Hydro Usermanual and installation guide - French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info