694278
41
Zoom out
Zoom in
Previous page
1/50
Next page
PELLET STOVES Chapter 4
INSTALLATION AND USE MANUAL
page 41
Operation Technical service - Rights reserved MCZ S.p.A. - Reproduction prohibited
ATTENTION
If the stove is not used as described in this instruction booklet,
the manufacturer refuses to accept any responsibility for
damage to persons and property that may arise. The
manufacturer furthermore refuses to accept responsibility for
damage to persons and property arising from the failure to
observe all the rules contained in the manual and in particular:
Failure when carrying out works of maintenance,
cleaning and repair to adopt all necessary measures and
precautions
Tampering with the safety devices.
Removing the safety devices.
Failure to connect the stove to an efficient system for the
discharge of smoke.
Failure to check in advance that the room where the
stove is to be installed is adequately ventilated.
4.17. ALARM SIGNALLING
If there is an operating anomaly, the stove goes into alarm shutdown
mode and informs the user of the type of problem that has occurred via
a 3-figure code displayed on the rear emergency panel.
The alarm is permanently signalled by the corresponding 3-figure code,
by a flashing red light on the emergency panel, and, for the first ten
minutes of the alarm, by a periodic acoustic signal. To take the stove
out of alarm conditions and restore its normal operation, read the
instructions in the next two paragraphs.
The following table summarizes the possible alarms which the stove
may signal and corresponding code which appears on the emergency
panel.
MESSAGE ON
DISPLAY
TYPE OF PROBLEM SOLUTION
A01
Fire fails to ignite
Check the level of pellets in the hopper.
Check that the grate is properly inserted in its housing
and does not have any obvious unburnt incrustations;
Check whether the ignition plug heats.
A02
Fire extinguishes abnormally
T
his is because the fire goes out due to lack of fuel
(hopper empty) or by an excess of pellets in the grate
which suffocates the flame.
A03
Pellet tank temperature exceeds foreseen
safety limit.
Overheating of the stove body
T
he structure is too hot because the product has been
operating for too long at maximum power, or it is
poorly ventilated, or the air fans are faulty. Place
selector D of the rear emergency panel in the OFF
position and wait for the stove to cool. When the stove
is cool enough, the A03 alarm indication on the display
will disappear. Place selector D of the panel in the
REMOTE position to restart the stove using the remote
control.
A04
T
he temperature of the smoke discharge has
exceeded pre-set safety limits
T
he stove will shut off automatically. Let the stove cool
off for a few minutes, then re-light it.
Check smoke release and position of the temperature
probe.
Check the type of pellet being used.
Downloaded from www.Manualslib.com manuals search engine
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MCZ SOLAR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MCZ SOLAR in the language / languages: English as an attachment in your email.

The manual is 3,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MCZ SOLAR

MCZ SOLAR Usermanual and installation guide - Dutch - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info