812457
63
Zoom out
Zoom in
Previous page
1/68
Next page
63
35-TROUBLESHOOTING
Technical Dept. - All rights reserved - Reproduction prohibited
CAUTION:
All repairs must be carried out exclusively by a specialised technician, with the stove completely cold and the electric
plug pulled out.
ANOMALY POSSIBLE CAUSES SOLUTIONS
The pellets are not fed into the combustion
chamber.
The pellet hopper is empty Fill the hopper with pellets
Sawdust has blocked the feed screw Empty the hopper and remove the sawdust
from the feed screw by hand
Faulty gear motor Replace the gear motor
Faulty electronic board Replace the circuit board
The re goes out or the stove stops
automatically
The pellet hopper is empty Fill the hopper with pellets
The pellets are not fed See the previous anomaly
The pellet temperature safety probe has
been triggered
Let the stove cool down, reset the
thermostat until the problem is
resolved and switch the stove back on.
If the problem persists contact Technical
Assistance.
Chrono active Check if the chrono setting is active
The door is not closed properly or the
gaskets are worn
Close the door and replace the gaskets
with original ones
Unsuitable pellets Change the type of pellets with those
recommended by the manufacturer
Low pellet supply Check the ow of fuel following the
instructions in the booklet.
The combustion chamber is dirty Clean the combustion chamber, following
instructions in the manual
Clogged outlet Clean the smoke duct
Faulty smoke extraction motor Check the motor and replace it, if neces-
sary
Water tank temperature too high Check correct operation of the water
circulation pump and the hydraulic system
in general.
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MCZ EGO HYDRO MATIC 12 M2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MCZ EGO HYDRO MATIC 12 M2 in the language / languages: English as an attachment in your email.

The manual is 8.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MCZ EGO HYDRO MATIC 12 M2

MCZ EGO HYDRO MATIC 12 M2 Installation Guide - English - 60 pages

MCZ EGO HYDRO MATIC 12 M2 User Manual - German - 68 pages

MCZ EGO HYDRO MATIC 12 M2 Installation Guide - German - 60 pages

MCZ EGO HYDRO MATIC 12 M2 User Manual - Dutch - 68 pages

MCZ EGO HYDRO MATIC 12 M2 Installation Guide - Dutch - 60 pages

MCZ EGO HYDRO MATIC 12 M2 User Manual - French - 68 pages

MCZ EGO HYDRO MATIC 12 M2 Installation Guide - French - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info