812474
25
Zoom out
Zoom in
Previous page
1/36
Next page
25
16-RECOMMENDATIONS FOR SAFE USE
Technical Dept. - All rights reserved - Reproduction prohibited
ONLY CORRECT INSTALLATION AND APPROPRIATE MAINTENANCE AND CLEANING OF THE APPLIANCE CAN GUARANTEE
CORRECT OPERATION AND SAFE USE OF THE PRODUCT
We would like to inform you that we are aware of cases of malfunctioning of domestic pellet-fuelled heating products, mainly due to
incorrect installation and inappropriate maintenance.
We would like to assure you that all of our products are extremely safe and certied according to European standards of reference. The
ignition system has been tested with the utmost attention to enhance ignition eciency and to prevent any type of problem, even in the
worst operating conditions. In any case, like for any other pellet-fuelled product, our appliances must be installed correctly and undergo
regular periodical cleaning and maintenance to guarantee safe operation. Our studies show us that malfunctioning is mainly due to the
combination of part or all of the following factors:
• Brazier holes obstructed or brazier deformed, due to lack of maintenance and conditions which can cause delayed ignitions,
generating an anomalous production of unburned gases.
• Insucient combustion air due to a reduced or clogged air inlet duct.
• Use of smoke ducts nonconforming to regulatory installation requirements, failing to guarantee an adequate draught.
• Partially clogged chimney, due to lack of maintenance, reducing the draught and making ignition dicult.
• End chimney pot nonconforming to the indications of the instruction manual, and therefore not suitable to prevent potential inverse
draught.
• This factor is crucial when the product is installed in especially windy areas, such as coastal regions.
The combination of one or more of these factors could generate important malfunctioning conditions.
To keep this from occurring, it is fundamental to guarantee that the product is installed in compliance with standards in force.
Furthermore it is of the utmost importance to respect the following simple rules:
• Every time the brazier is removed for cleaning, it must always be put back properly in the work position before using the product,
completely removing any residual lth left on the support base.
• Pellets must never be loaded in the brazier manually, either before ignition or during operation.
• The accumulation of unburned pellets ensuing a failed ignition must be removed before repeating ignition. Also check that they are
fed correctly and that the combustion air inlet/smoke outlet are regular.
• If ignition fails repeatedly, immediately suspend use of the product and contact a qualied technician to check its operation.
Compliance with these indications is absolutely sucient to guarantee proper operation and to avoid any type of problems with the
product.
If the above-mentioned precautions are not taken, and during ignition the brazier is overloaded with pellets thus generating anomalous
smoke in the combustion chamber, carefully follow the indications below:
• Do not disconnect electrical power to the product for any reason whatsoever: this would stop the smoke extractor, releasing smoke
into the environment.
• Take the precaution of opening the windows to ventilate the installation room from any smoke in the environment (the chimney
might not work properly).
• Do not open the re door: this would compromise regular operation of the smoke extraction system to the chimney.
• Just switch the stove o by acting on the on-o button on the control panel (not the rear power supply socket button!) and move
away until smoke has been completely extracted.
• Before attempting re-ignition, clean the brazier and its air passage holes completely of all deposits and unburned pellets. Put the
brazier back in place, removing any residue from its support base. If ignition fails repeatedly, immediately suspend use of the product
and contact a qualied technician to check its operation and the chimney.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MCZ CLIO HYDRO 23 S2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MCZ CLIO HYDRO 23 S2 in the language / languages: English as an attachment in your email.

The manual is 2.72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MCZ CLIO HYDRO 23 S2

MCZ CLIO HYDRO 23 S2 Installation Guide - English - 48 pages

MCZ CLIO HYDRO 23 S2 User Manual - German - 48 pages

MCZ CLIO HYDRO 23 S2 User Manual - German - 36 pages

MCZ CLIO HYDRO 23 S2 Installation Guide - Dutch - 48 pages

MCZ CLIO HYDRO 23 S2 User Manual - Dutch - 36 pages

MCZ CLIO HYDRO 23 S2 Installation Guide - French - 48 pages

MCZ CLIO HYDRO 23 S2 User Manual - French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info