632407

MCZ Boxtherm 70 Manual

37
Zoom out
Zoom in
Previous page
1/52
Next page
35
6-SAFETY DEVICES AND ALARMS
A10
The spark plug is faulty. Contact an authorised service centre to have the
component replaced.
A11
Pellet supply fault. Contact an authorised service centre to have the
component replaced.
A12
The remote control has been out of the product
reception range for over 3 hours (or the batteries
are at).
NOTE: the appliance does not enter the
shutdown phase due to an alarm only in such a
case, and continues to work in the mode set by
the remote control via the last command.
Move the remote control within the product reception
range (or change the batteries of the remote control if
they are at). The alarm alerts will disappear as soon
as the appliance receives a new signal from the remote
control. A simple way of forcing signal transmission to
the product is by pressing button 4 (which changes the
operating mode from manual to automatic and vice
versa).
A13
General fault in the electronic control unit. Contact an authorised service centre to have the
component replaced.
A14
Faulty air ow rate sensor. This alarm does not block the system and only a
warning screen is displayed. Contact an authorised
service centre to have the component replaced.
SEr
Routine maintenance alert. This ashing message upon start-up indicates that the
preset operating hours before maintenance is due have
elapsed and a qualied technician, recommended by
the manufacturer, must be contacted for maintenance
to be performed.
DELETING THE ALARM STATUS
Follow the procedure described below to restore normal product operation after an alarm has been triggered:
•  Set selector D on the rear emergency panel to OFF for a few seconds until the 3 digit alarm identication code disappears. The red LED
stops ashing and the alarm buzzer is silenced by performing the steps below.
•  Set selector D back to the REMOTE position for product operation to be remote controlled.
•  Switch the remote control o and then on again if the appliance is to be switched on.
Only if alarm A12 is triggered (no communication between the remote control and the product), the appliance
remains on according to the last mode set and automatically exits the alarm mode when the rst signal is received
from the remote control.
Technical Dept. - All rights reserved - Reproduction is prohibited
Downloaded from www.Manualslib.com manuals search engine
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MCZ Boxtherm 70 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MCZ Boxtherm 70 in the language / languages: English as an attachment in your email.

The manual is 6,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MCZ Boxtherm 70

MCZ Boxtherm 70 Usermanual and installation guide - Dutch - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info