684104
6
Zoom out
Zoom in
Previous page
1/8
Next page
1. PLACEMENT OF AND CONNECTING THE CHARGING STATION
See chapter Installation in the Operator’s Manual
1. Place the charging station at a central position in the working area, with a lot of open space in front of the charging station
and on a relatively horizontal surface.
2. Connect the power supplys low voltage cable to the charging station and the power supply.
3. Connect the power supply to a
100-240
V wall socket.
4. Place the robotic lawnmower in the charging station to charge the battery while the boundary wire is laid. Press the ON/
OFF button to turn the product on.
2. PLACEMENT OF THE BOUNDARY WIRE AND THE GUIDE WIRE
See chapter Installation in the Operator’s Manual
1. Lay the boundary wire so that it forms a loop around the working area.
2. Make an eyelet at the point where the guide wire will later be connected.
3. Run the guide wire to the point on the boundary loop where the connection will be made. Avoid laying the wire at tight
angles.
3. CONNECTING THE BOUNDARY WIRE AND THE GUIDE WIRE
See chapter Installation.in the Operators Manual
1. Fasten the guide wire in snap locks at the bottom of the charging station.
2. Open the connectors and lay the wire ends in the recesses on each connector.
3. Press the connectors together using a pair of pliers.
4. Cut o any surplus boundary wire. Cut 1 to 2 cm / 0,4 to 0,8” above the connectors.
5. Press the connectors onto the contact pins, marked L (left) and R (right), on the charging station. It is important that the
right-hand wire is connected to the right-hand contact pin, and the left-hand wire to the left-hand pin.
6. Fasten the connector to the contact pin marked Guide on the charging station.
4. CONNECTING THE GUIDE WIRE TO THE BOUNDARY WIRE
See chapter Installation in the Operator’s Manual
1. Cut the boundary wire with a wire cutters at the centre of the eyelet that was made in step 2.2.
2. Connect the guide wire to the boundary wire using the accompanying couplers. Press the couplers completely together
with an adjustable pliers.
5. STARTING AND STOPPING
See chapter Operation in the Operator’s Manual
STARTING
1. Open the hatch to the keypad.
2. Push the ON/OFF button. The display is lit up.
3. Use the up/down arrow buttons and the OK button to enter the PIN code. Close the hatch.
STOPPING
Press the STOP button.
6.
ADJUSTING THE ROBOTIC LAWNMOWER TO SUIT THE SIZE OF YOUR
LAWN
See chapter Operation in the Operator’s Manual
The mowing results depend on mowing time. Adjust the mowing time to suit your garden using the Schedule function. You
decide what times during the day the robotic lawnmower is to work. The robotic lawnmower mows about 40-42 / 430-452
sq. ft. per hour and day. For example; if your garden consists of 300 / 3200 sq. ft. of grass, the robotic lawnmower should
work on average 7-7.5 hours per day.
7. MAINTENANCE
See chapter Maintenance in the Operator’s Manual
1. Turn o the product during all work on the product, such as cleaning or replacing the blades. Check that the indicator lamp
on the keypad is not lit.
2. Never use solvents for cleaning.
3. All connections to the charging station (power supply, boundary and guide wire) must be disconnected if there is a risk of a
thunderstorm.
4. Fully charge the battery at the end of the season before winter storage.
EN
QG_1140738_ROB_R400_R500_R600_201812.indd 6 2018-12-18 11:19:18
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch ROB S600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch ROB S600 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 6,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of McCulloch ROB S600

McCulloch ROB S600 User Manual - English - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info