684105

McCulloch ROB R600 Manual

15
Zoom out
Zoom in
Previous page
1/52
Next page
CAUTION: The robotic lawnmower must never
run over gravel, mulch or similar material which
can damage the blades.
CAUTION: If the working area is adjacent to
water bodies, slopes, precipices or a public
road, the boundary wire must be supplemented
with an edging or the like. It must then be at
least 15 cm in height. This will prevent the
robotic lawnmower from ending up outside the
working area under any circumstance.
min. 15 cm / 6"
3.5.3 Boundaries within the working area
Use the boundary wire to isolate areas inside the
working area by creating islands around obstacles which
cannot withstand a collision, for example flowerbeds,
bushes and fountains. Lay the wire up to and around the
area to be isolated, and then return it back along the
same route. If pegs are used, the wire should be laid
under the same pegs on the return route. When the
boundary wires to and from the island are laid close
together, the robotic lawnmower can drive over the wire.
0 cm / 0
"
CAUTION: The boundary wire may not be
crossed on its way to and from an island.
Obstacles that can withstand a collision, for example,
trees or bushes taller than 15 cm, do not need to be
isolated with the boundary wire. The robotic lawnmower
will turn around when it collides with this type of
obstacle.
However, to achieve careful and silent operation, it is
recommended to isolate all fixed objects in and around
the working area.
Obstacles that slope slightly, for example stones or large
trees with raised roots, must be isolated or removed.
Otherwise the robotic lawnmower can slide up onto this
kind of obstacle causing the blades to be damaged.
3.5.3.1 Secondary areas
If the working area consists of two areas which the
robotic lawnmower has difficulty travelling between, it is
recommended to set up a secondary area. Instances of
this are 25% slopes or a passage that is narrower than
60 cm. Lay the boundary wire then around the
secondary area so that it forms an island outside of the
main area. The robotic lawnmower must be moved
manually between the main and secondary area when
the lawn in the secondary area has to be cut.
Secondary
area
Main area
The
MAN
operating mode must be used as the robotic
lawnmower cannot travel on its own from the secondary
area to the charging station. See
Operation selection on
page 33
. In this mode, the robotic lawnmower will
never look for the charging station but will mow until the
battery runs out. When the battery is flat, the robotic
lawnmower will stop and the
Needs manual charging
message will appear in the display. Place the robotic
lawnmower in the charging station to charge the battery.
If the main area has to be cut straight after charging, the
358 - 001 - 21.09.2017 Installation - 15
… 15 …


Need help? Post your question in this forum.

Forumrules
1

Forum

mcculloch-rob-r600

Reset search

  • hi, i have a rob r600 since 4 years, 3500 hours of work, lately stop work right in the middle of the garden with blank display, no powered. After i dispose the rob in the charging home i have to insert as the first time language, time etc etc. Once is full charge starthis job but stop again the some day.
    Any suggestion? software? need new battery?
    thanks
    Alf Submitted on 3-11-2022 at 08:05

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch ROB R600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch ROB R600 in the language / languages: English as an attachment in your email.

The manual is 5,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of McCulloch ROB R600

McCulloch ROB R600 Quick start guide - English - 8 pages

McCulloch ROB R600 User Manual - German - 56 pages

McCulloch ROB R600 Quick start guide - German - 8 pages

McCulloch ROB R600 User Manual - Dutch - 56 pages

McCulloch ROB R600 Quick start guide - French, Italian - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info