Manual McCulloch PM E1900-16 (page 10 of 15) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

478434

Zoom out

Zoom in

1/15

ENGLISH – 7

new; after the first assembly, the chain tension must be controlled after 5 minutes machine operation); in any

case do not tighten the chain immediately after use, but wait until it cools down.

In cases where the loosened chain needs to be adjusted, always unscrew the bar retaining nut/ knob before

adjusting the chain tensioner screw/ring; adjust the tension and tighten the bar retaining nut/ knob accordingly.

E. START-UP AND ARREST

1,4,5,6,7,8,9,11,12,13

Start-up: grip both handles firmly, release the chain

brake lever, press and maintain the switch block

pressed in, then press the switch (at this point the

switch block can be released).

Arrest: The machine will stop whenever the switch is

released. In the case where the machine does not

stop, activate the chain brake, disconnect the cable

from the main line socket and take the machine to the

Authorised Service Centre.

F. BAR AND CHAIN LUBRICATION

3,6,7,8,9,12

ATTENTION! Insufficient lubrication will provoke

chain breaking and can cause serious and even

mortal injury.

Bar and chain lubrication is performed by an

automatic pump.

Choice of chain oil

Always use new oil only (special type for chains) with

adequate viscosity: the oil must adhere well and

guarantee good running properties in both winter and

summer. If chain oil is not available, EP 90

transmission oil can be used.

Never use waste oil because this is this harmful to

health, the machine and the environment. Make sure that

the oil is suitable for the temperature of the environment

where the tool will be used: For temperatures under 0°C

certain oils become denser, overloading the pump and

causing damage. Contact your Authorised Service

Centre for advice on oil choice.

Filling oil tank

Unscrew the oil tank cap, and fill the tank taking care

not to spill any oil (if this occurs clean the machine

carefully) (fig.2), and then screw the cap back on

tightly.

G. MAINTENANCE

1,2,3,4,5,6,7,8,9,12,13

ATTENTION! In cases where work environments are

particularly dirty or dusty, the operations described

must be performed more frequently than mentioned

in the instructions.

Before each use

Control that the chain oil pump functions correctly:

direct the bar towards a clear surface at a distance of

about 20 centimetres; after the machine has run for

about a minute, the surface should show clear traces

of oil(fig.1).

Check that excessive strength is not needed for

activating and deactivating the chain brake. Also

check that it is not activated too easily and that it is

not blocked. Then check chain brake function as

follows: release the chain brake, grip the machine

correctly and start up the machine, activate the chain

brake by pushing the front hand guard forward with

the left wrist or arm but without removing the hand

from the handle(fig.2). If the chain brake is working

correctly, the chain should be blocked immediately.

Check that the chain is sharpened correctly (See

below), in good working condition and that the

tension is correct. If the chain is irregularly worn, or if

the cutting teeth are only 3 mm high, the chain must

be replaced(fig.3).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch PM E1900-16 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

McCulloch PM E1900-16 Manual

Product: