684274
18
Zoom out
Zoom in
Previous page
1/60
Next page
18
1. Starthandgriff
2. Chokehebel
3. Zündkerzenkabel und Kerzenstecker
4. Schalthebelanzeiger
5. Antriebshebel “ausgekuppelt”
6. Antriebshebel “eingekuppelt”
7. Antriebshebel in “entriegelter” Stellung
8. Antriebshebel in “verriegelter” Stellung
9. Gashebel
10. Handgriff
Abb. 6
Abb. 7
3
Abb. 8
Motorstart
a. Zündkerzenkabel und Kerzenstecker (Abb. 6) lösen.
b. Schalthebel auf “N” (Neutralstellung) einstellen (Abb. 7).
c. Gashebel (Abb. 8) “FAST” (schnell) einstellen.
d. Chokehebel auf “CHOKE” stellen (Abb. 6).
e. Mit der einen Hand den Starthandgriff (Abb. 6) und mit
der anderen Hand die Lenkstange greifen. Das Seil
langsam herausziehen, bis sich der Motor am Anfang
des Verdichtungstaktes befindet (das Seil läßt sich an
diesem Punkt etwas schwerer ziehen).
f. Das Seil mit einer schnellen, energischen Armbewegung
herausziehen. Den Starthandgriff fest greifen und das
Seil langsam zurückgleiten lassen. Den Starthandgriff
darf nicht in Richtung Anlasser zurückschnappen.
g. Punkte (e.) und (f.) wiederholen, bis der Motor startet.
Wenn der Motor startet, ist der Chokehebel in der Mitte
zwischen “CHOKE” und “RUN” einzustellen und nach
Erwärmung des Motors ganz auf “RUN” zu stellen (Abb. 6).
h. Gashebel (Abb. 8) für einige Minuten in der Mitte zwischen
“FAST” (schnell) und “STOP” (stop) einstellen, um den
Motor zu erwärmen.
WARNUNG!
Beim Starten des Motors muss der Antriebshebel immer auf
Position “ausgekuppelt” gestellt sein (Abb. 8).
HINWEIS!
Ein neuer Motor benötigt bei niedriger Drehzahl ca. 3-5 Mi-
nuten, bis der Motor im Leerlauf gleichmäßig läuft. Die Leer-
laufdrehzahl ist nach dieser Einlaufperiode richtig eingestellt.
Zinkenbetrieb
a. Gashebel auf die gewünschte Geschwindigkiet einstellen.
b. Um die Bodenfräse in Bewegung zu setzen, zunächst
den Antriebshebel entriegeln und dann den Hebel in
Stellung “eingekuppelt” drücken (Abb. 8).
WARNUNG!
Den Antriebshebel immer auskuppeln, bevor Sie den Schal-
thebel in eine andere Stellung bewegen. Wird der Antrieb-
shebel losgelassen, wird der Antrieb ausgekuppelt.
1
2
3
7
8
9
6
5
10
4
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch MRT6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch MRT6 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info