Manual McCulloch Mac4-18XT (page 11 of 15) (English, German, French, Spanish)

478397

Zoom out

Zoom in

1/15

S Be alert to signs that the tree is ready to fall:

cracking sounds, widening of the felling cut,

or movement in the upper branches.

S As tree starts to fall, stop saw , put it down,

and get away quickly on your planned re-

treat path.

S DO NOT cut down a partially fallen tree with

your saw . Be extremely cautious with par-

tially fallen trees that may be poorly sup-

ported. When a tree doesn’t fall completely,

set the saw aside and pull down the tree with

a cable winch, block and tackle, or tractor.

CUTTING A F ALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen

tree to the desired log length.

WARNING: Do not stand on the log

being cut. Any portion can roll causing loss

of footing and control. Do not stand downhill

of the log being cut.

Important points

S Cut only one log at a time.

S Cut shattered wood very carefully; sharp

pieces of woodcould beflung toward oper-

ator.

S Use a sawhorse to cut small logs. Never

allow another person to hold the log while

cutting and never hold the log with your leg

or foot.

S Do n ot cut in an area where logs, limbs,

and roots are tangled. Drag the logs into a

clear area before cutting b y pulling out ex-

posed and cleared logs first.

TYPES OF CUTTING USED FOR

BUCKING

WARNING: If saw becomes pinched

or hung in a log, don’t try t o force it out. You

can lose control of the saw resulting in injury

and/or damage to the saw. Stop the saw,

drive a wedge of plastic or wood into the cut

until the saw can be removed easily. Restart

the saw and carefully reenter the cut. Do not

attempt torestart your saw when it is pinched

or hung in a log.

Turn saw OFF and use a plastic or

wooden wedge to force cut open.

Overcutting begins on thetop side of thelog

with the saw against the lo g. When overcut-

ting use light downward pressure.

Overcutting

Undercutting

Undercutting involves cutting on the under-

side of the log with top of saw against the log.

When undercutting use light upward pres-

sure. Hold saw firmly and maintain control.

The saw will tend to push back toward you.

WARNING: Never turn saw upside

down to undercut. The saw cannot be con-

trolled in this position.

First c ut on pressure side of log

Second cut

First cut on pressure side of log

Second cut

BUCKING WITHOUT A

SUPPORT

S Overcut through 1/3 of the diameter of the

log.

S Roll the log over and finish with a second

overcut.

S Give special attention to logs under strain

to prevent the saw from pinching. Make

the first cut on the pressure side to relieve

the stress on the log.

BUCKING USING A LOG OR SUP-

PORT STAND

S Remember your first cut is always on the

pressure side of the log.

S Your first cut should extend

1/3 of the

diameter of the log.

S Finish with your second cut.

Cut

Usingalogforsupport

Cut

Using a support stand

Cut

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch Mac4-18XT in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

McCulloch Mac4-18XT Manual

Product: