Manual McCulloch Mac316XT (page 4 of 15) (English, German, French, Spanish)

478399

Zoom out

Zoom in

1/15

S Do not put pressure on the saw at the end of

the cut. Applying pressure can cause you to

lose control when the cut is completed.

S Stop the engine before setting the saw

down.

S Do not operate a chain saw that is dam-

aged, improperly adjusted, or not com-

pletely and securely assembled. Always

replace bar, chain, hand guard, or chain

brake immediately if it becomes damaged,

broken or is otherwise removed.

S With the engine stopped, hand carry the

chain saw with the muffler away from your

body , and the guide bar and chain to the

rear, preferably covered with a scabbard.

CHAIN SAW SAFETY EQUIPMENT

NOTE:

In this section, t h e safety featur e s of

the chain saw and their function are explained.

For inspection and maintenance, see instruc-

tio n s i n the CHEC KI NG, MAINTAI NI NG AND

SERVICING CHAIN SAW SAFETY EQUIP-

MENT section. See instructions under the

WHAT IS WHA T? section, to find where these

parts are located on your chain saw . The life

span of the machine can be reduced and the

risk of accidents can increase if machine main-

tenance is not carried out correctly and if ser-

vice and/or repairs are not carried out profes-

sionally . If you need further information, please

contact your nearest service dealer .

S Chain brake. Your chain saw is equipped

with a chain brake that is designed to stop

the chain from moving.

WARNING: The chain brake is de-

signed to stop the chain immediately if you

get a kickback. The chain brake reduces the

risk of accidents, but only you can prevent

them. DONOT ASSUME THAT THE CHAIN

BRAKE WILL PROTECT YOU IN THE

EVENT OF A KICKBACK.

S Throttle trigger lock--out. The th rottle

lock--o ut is designed to prevent accidental

operation of the throttle trigger .

S Chain catcher. The chain catcher is de-

signed to catch the saw chain if it breaks.

S Vibration damping system. Your chain

saw is equipped with a vibration damping

system that is designed to minimize vibra-

tion an d make operation easier.

SAFETY NOTICE: Exposure to vibrations

through prolonged use of gasoline powered

hand tools could cause blood vessel or nerve

damage in the fingers, hands, and joints of peo-

ple prone to circulation disorders or abnormal

swellings. Prolonged use in cold weather has

been linked to blood vessel damage in other-

wise healthy people. If symptoms occur such

as numbness, pain, loss o f strength, change in

skin color or texture, or loss of feeling in the fin-

gers, hands, or joints, discontinue the use of

this tool and seek medical attention. An anti-

vibration system does not guarantee the avoid-

ance of these problems. Users who operate

power tools on a continual and regular basis

must monitor closely their physical condition

and the condition of this tool.

S ON/STOP switch. The ON/STOP switch

should be used to stop the engine.

CHECKING, MAINTAINING AND

SERVICING CHAIN SAW SAFETY

EQUIPMENT

WARNING: Never use a chain saw

with defective safety equipment. Safety

equipment must be inspected and main-

tained. If your chain saw does not pass in-

spection, take the saw to your nearest ser-

vice dealer for repair.

S Chain brake. Brush off any wood dust, res-

in and dirt from the chain brake and clutch

drum. Dirt and wear can impair operation of

the brake. For additional i nformation, see

OPERATING YOUR UNIT section.

S Throttle trigger lock--out. Check that the

throttle trigger can not beoperated untilthe

throttle lock--o ut is pressed.

S Chain catcher. Check that the chain

catcher is not damaged and is firmly at-

tached to the body of the chain saw .

S Vibration damping system. Regularly

check the vibration damping units for

cracks or deformation. Make sure the

vibration damping units are securely at-

tached to the engine unit and handle unit.

S ON/STOP switch. Start the engine and

make sure the engine stops when you

move the ON/STOP switch to the ST OP

position.

MAINTAIN YOUR SAW IN GOOD

WORKING ORDER

S Have all chain saw service performed by a

qualified service dealer with the exception of

the items listed in the maintenance section of

this manual. For example, if improper tools

are used to remove or hold the flywheel

when servicing the clutch, structural damage

to the flywheel can occur and cause the fly-

wheel to burst.

S Make certain th e saw chain stops moving

when the throttle trigger is released. For

correction, refer to CARBURETOR AD-

JUSTMENTS.

S Never modify your saw in any way. Use

only attachments supplied or specifically

recommended by the manufacturer.

S Keep the handles dry, clean, and free of oil

or fuel mixture.

S Keep fuel and oil caps, screws, and fas-

teners securely tightened.

S Use only McCulloch accessories and re-

placement parts as recommended.

HANDLE FUEL WITH CAUTION

S Do not smoke while handling fuel or while

operating the saw .

S Eliminate all sources o f sparks or flame i n

the areas where fuel is mixed or poured.

There should be nosmoking, open flames,

or work that could cause sparks. Allow en-

gine to cool before refueling.

S Mix and pour fuel in an outdoor area on bare

ground; store fuel in a cool, dry, well venti-

lated place; and use an approved, marked

container for all fuel purposes. Wipe up all

fuel spills before starting saw.

S Move at least 10 feet (3 meters) from fuel-

ing site before starting engine.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch Mac316XT in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

McCulloch Mac316XT Manual

Product: