478390
7
Zoom out
Zoom in
Previous page
1/19
Next page
7
ATTACHING THE BAR & CHAIN
(If not already attached)
WARNING: Recheck each assem-
bly step ifthe saw is received assembled.Al-
ways wear gloves when handling the chain.
The chain is sharp and can cut you even
when it is not moving!
1. Loosen and rem ove bark nobcompletely
by lifting lever and turning counterclock-
wise.
LOOSEN
2. Remove clutch cover. Remove the plas-
tic shipping spacer (if p resent).
3. Slide guide bar on bar bolts until guide
bar stops against clutch drum sprocket.
4. Carefully remove the chain from the pack-
age. Hold chain with the drive links as
sho wn .
CUTTERS MUST FACE IN
DIIRECTION O F RO TATION
Tip of
Bar
Cutters
Depth Gauge
Drive Links
5. Place chain over and behind clutch re-
tainer, fitting the drive links in the clutch
drum sprocket.
6. Fit bottom of drive links between the
teeth in the sprocket in the nose of the
guide bar.
7. Fit chain drive links into bar groove.
8. Pull guide bar forward until chain is snug
in guide bargroove. Ensure all drive links
are in t he bar groove.
9. Install clutch cover. Be sure adjusting pin is
in the adjusting pin hole in the guide bar.
CAUTION: It is very important when instal-
ling the clutch cover th at the adjusting pin
aligns in to the adj usting pin hole in the bar . Fail-
ure to i nstall the clutch cover correctly may re-
sult in permanent dam age to your chain saw.
Back
view of
clutch
cover
Adjusting pin
10. Install bar knob and finger tighten only.
Do not tighten any further at this point.
Once the chain is tensioned, you will
need to t ighten the bar knob.
CHAIN TENSION (Including units
with chain already installed)
NOTE
: When adjusting chain tension,
make sure the bar knob is loosened 1 ½ -- 2
turns. Attempting to tension the chain when
the bar knob is tight can cause damage.
Checking the tension:
Use a screwdriver to move chain ar ound guide
bar . I f t he chain does n ot rotate, it is too tight. If
too loose, the chain will sag below the bar.
Adjusting
wheel
Bar knob
Screwdriver
Guide bar
Adjusting the tension:
Chain tension is very important. Chain
stretches during use. This is especially true
during the first few times you use your saw.
Always check chain tension each time you
use and refuel your saw.
1. Lift lever on bar knob and turn counter-
clo ckwise 1 ½ -- 2 turns to loosen clutch
cove r.
LOOSEN
2. Turn adjusting wheel (downward direc-
tion) to tension chain until chain solidly
contacts bottom of guide bar rail. Lift tip
of guide bar w hile adjus ting t ension.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch M4620 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch M4620 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info