684167
22
Zoom out
Zoom in
Previous page
1/108
Next page
22
2
INSTALL SEAT
Remove bolts and winged washers se cur ing seat to cardboard
packing and set aside for as sem bly of seat to tractor. Remove
the cardboard packing and discard.
IMPORTANT: Do not remove tape (1) from adjustment handle
until seat is properly secured to tractor.
Connect wiring harness (2) to the seat switch (3).
NOTE: All three pads will not install at the same time. The
middle pad must be installed first before other pads will align
with assembly holes.
Place seat on seat pan (4) so middle pad (5) is aligned
with middle slot (6) assembly hole.
Insert pad and pull seat towards rear of tractor until front
two pads (7) align with front slot assembly holes (8).
Insert pads by providing evenly distributed light downward
pressure and pull seat towards rear of tractor (9), making
sure front pads are engaged on the seat pan.
Raise seat. Assemble bolts (10) and winged washers
(11) and tighten securely to front pads (12).
NOTE: Ensure “UP” reads right side up and arrow is pointing
up on winged washers as shown.
Remove tape (13) and discard.
WARNING: Ensure the seat assembly is securely fastened to
the seat pan before occupying or operating tractor.
Lower seat into operating position and sit on seat. Press
clutch/brake pedal all the way down. If operating position
is not comfortable, adjust seat.
TO ADJUST SEAT
Grasp adjustment handle (14) and pull up. Slide seat to desired
position and release adjustment handle.
IMPORTANT: Before operating tractor, ensure operator pres-
ence switch is functioning properly (see “CHECK OPERATOR
PRESENCE SYSTEM” in the MAINTENANCE section of this
manual).
9
10
11
11
13
12
14
2
3
7
7
1
4
8
8
5
6
EINBAU DES SITZES
Entfernen Sie die Schrauben und die Flügelscheiben, mit denen
der Sitz an der Verpackung befestigt ist, und legen Sie diese
für den Einbau des Sitzes am Gerät beiseite. Entfernen Sie
die Verpackung und entsorgen Sie sie anschließend.
WICHTIG: Entfernen Sie nicht das Klebeband (1) vom
Einstellhebel, bis der Sitz ordnungsgemäß am Gerät befestigt ist.
Verbinden Sie den Kabelbaum (2) mit dem Sitzschalter (3).
HINWEIS: Die drei Pads werden nicht gleichzeitig montiert.
Das mittlere Pad muss montiert werden, bevor andere Pads
an den Montagelöchern ausgerichtet werden.
Positionieren Sie den Sitz so in der Sitzschale (4), dass
das mittlere Pad (5) an dem mittleren Schlitz (6) der
Montagelöcher ausgerichtet ist.
Setzen Sie das Pad ein und ziehen Sie den Sitz in
Richtung Heckseite des Geräts, bis die vorderen beiden
Pads (7) mit den vorderen Schlitzen der Montagelöcher
(8) übereinstimmen.
Setzen Sie die Pads mit gleichmäßigem Druck ein und
ziehen Sie die Sitze in Richtung der Heckseite des Geräts
(9), um sicherzustellen, dass die vorderen Pads auf der
Sitzschale einrasten.
Heben Sie den Sitz an. Drehen Sie die Schrauben (10)
und Flügelscheiben (11) ein und befestigen Sie diese an
den vorderen Pads (12).
HINWEIS: Stellen Sie sicher, dass der Schriftzug „UP“ korrekt
lesbar ist, und der Pfeil wie abgebildet auf die Flügelscheiben
zeigt.
Entfernen Sie das Klebeband (13) und entsorgen Sie es.
WARNUNG: Stellen Sie sicher, dass die Sitzbaugruppe sicher
an der Sitzschale befestigt ist, bevor Sie sich auf das Gerät
setzen oder es in Betrieb genommen wird.
Senken Sie den Sitz in die Betriebsposition ab und set-
zen Sie sich auf den Sitz. Treten Sie das Kupplungs-/
Bremspedal ganz durch. Wenn die Betriebsposition nicht
bequem ist, stellen Sie den Sitz ein.
EINSTELLEN DES SITZES
Greifen Sie den Einstellhebel (14) und ziehen Sie ihn hoch.
Bringen Sie den Sitz in die gewünschte Position und lassen
Sie den Einstellhebel los.
WICHTIG: Stellen Sie vor der Inbetriebnahme des Traktors
sicher, dass der Totmannschalter ordnungsgemäß funktioniert
(siehe „KONTROLLE DER TOTMANNEINRICHTUNG“ im
Abschnitt WARTUNG dieser Bedienungsanleitung).
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch M125-97TC Powerdrive at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch M125-97TC Powerdrive in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info