684137

McCulloch Li58-26 M40 Manual

14
Zoom out
Zoom in
Previous page
1/320
Next page
LED screen Possible faults Possible steps
All four battery capacity and power
LEDs flash, no other LEDs come
on after pressing the power button
Motor control handle held
down when the power but-
ton is pressed for the first
time or internal motor con-
trol handle switch failure
Release the motor control handle. If the motor
control handle is not held down and the LEDs
continue to flash, speak to an approved service
center.
Product stops operating and all
four battery capacity LED's flash,
no other LEDs come on.
Battery pack is loose in
the powerhead and no
longer makes good con-
tact, battery pack is too
warm, or cold or other in-
ternal battery error
1. Stop the product.
2. Remove battery pack from product and press
the indicator button on the battery pack to
show the error code. The LED's on the battery
pack come on and show an error code.
3. Read the included battery manual for a list of
related LED error codes for possible faults and
procedures.
If the battery pack does not show an error after
pressing the indicator button on the battery pack
and only displays the state of charge, the battery
pack may have come loose in the powerhead dur-
ing operation. Install the battery pack correctly into
the powerhead until a click is heard.
Product stops operating and the
power button flashes while the bat-
tery capacity LED's continue to
show the current state of charge
Cutting chamber is clog-
ged with grass, motor con-
troller is too warm, or mo-
tor fault
1. Stop the product.
2. Remove the battery pack and turn the product
on its side with the user control interface point-
ing up.
3. Examine the blade, blade bolt, blade assem-
bly, motor and motor base for damage. Clear
all grass from the bottom of the machine and
examine for clogs.
4. Install the battery pack and follow the starting
procedure to start the machine.
If the error continues to show, let the product cool
down. The motor controller may be too warm for
operation. If the error continues to show, speak to
an approved service center.
TRANSPORTATION AND STORAGE
• Keep equipment safe during transportation to
prevent damage and accidents.
• For storage, keep equipment in a locked area away
from children and persons that are not approved.
• For storage, keep the product and equipment in a
dry and frost-proof area.
• When loading or moving the product, do not go more
than the maximum recommended operation angle of
15 degrees.
• Clean the product. For more information, see
To
clean the product on page 12
.
• Lubricate the product.
• Tighten bolts and nuts.
• Replace or repair damaged components.
• Touch up all rusted or damaged paint surfaces.
Sand lightly before painting.
• Use the correct protective cover on the product that
does not keep moisture. Do not use plastic because
it cannot breathe, lets condensation collect and
causes corrosion on the product.
• Always remove the battery pack prior to
transportation or storage.
14 778 - 004 - 23.10.2018
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch Li58-26 M40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch Li58-26 M40 in the language / languages: All languages as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info